SPEED LIMITER SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Hybrid Control / Data List.

    5. Read the Data List according to the display on the GTS.


      Powertrain > Hybrid Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ASL SW Speed limiter switch signal ON or OFF

      OFF: Speed limiter switch off

      ON: Speed limiter switch on

      		 -
      ASL Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) Actual vehicle speed displayed -
      ASL Memory Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) Vehicle speed stored in memory -
      ASL Request Limit Driving Force Speed limiter request limit driving force Min.: -10 kN, Max.: 9.92 kN - -
      ASL Request Gear Position Transaxle gear request signal 0 to 255 Gear Required transaxle gear "None" is always displayed.
      TRC/VSC OFF Indicator TRC/VSC OFF indicator signal ON or OFF

      OFF: TRC/VSC OFF indicator not illuminated

      ON: TRC/VSC OFF indicator illuminated

      		 -
      ASL Cancel History (Lost Communication with Brake System) Speed limiter cancel history (lost communication with brake system) ON or OFF

      OFF: Speed limiter cancel history (lost communication with brake system) does not exist

      ON: Speed limiter cancel history (lost communication with brake system) exists

      		 -
      ASL Cancel History (Speed Sensor Malfunction) Speed limiter cancel history (speed sensor malfunction) ON or OFF

      OFF: Speed limiter cancel history (speed sensor malfunction) does not exist

      ON: Speed limiter cancel history (speed sensor malfunction) exists

      		 -
      Kickdown Switch Kickdown Switch signal ON or OFF

      OFF: Accelerator pedal released

      ON: Accelerator pedal fully depressed

      		 -
      ASL Limiting Driving Force ASL limiting driving force operation condition Inactive or Active

      Active: ASL limiting driving force is operating

      Inactive: ASL limiting driving force is not operating

      		 -
      ASL Ready Speed limit standby condition ON or OFF

      OFF: Speed limiter switch off

      ON: Speed limiter switch on

      		 -

  2. PERFORM ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Tech Tips

      The power switch must be turned on (IG) to proceed with the Active Test using the GTS.


      Body Electrical > Combination Meter > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Meter Display 1 Main display, multi-information display and clock OFF or All -