FUEL PUMP(w/ Canister Pump Module) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump with filter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Adaptive high beam system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Replacement of fuel pump with filter assembly Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here

*1: When performing learning using the GTS.
Click here Click here

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE REAR SEAT ASSEMBLY

    Click here

  5. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  6. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  7. REMOVE REAR UNDER SIDE COVER LH

    Click here

  8. REMOVE REAR UNDER SIDE COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  9. REMOVE REAR UNDER COVER

    Click here

  10. REMOVE REAR CONSOLE BOX COVER

    Click here

  11. REMOVE REAR SEAT CONSOLE BOX ASSEMBLY

    Click here

  12. REMOVE CENTER REAR SEATBACK HINGE SUB-ASSEMBLY


    1. B006HBZ

      Disconnect the rear seat inner belt assembly LH connector.

    2. Disengage the clamp to disconnect the wire harness from the center rear seatback hinge sub-assembly.

    3. Remove the 2 bolts and center rear seatback hinge sub-assembly from the vehicle body.

  13. REMOVE REAR FLOOR SERVICE HOLE COVER


    1. B006J5DC01
      *a Protective Tape

      Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.

    2. B006HKB

      Disconnect the fuel pump connector and fuel tank pressure sensor (vapor pressure sensor) connector.

  14. REMOVE FUEL TANK PRESSURE SENSOR (VAPOR PRESSURE SENSOR)

    Click here

  15. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY


    1. B006IV1

      Disconnect the fuel tank vent hose sub-assembly from the fuel suction tube with pump and gauge assembly.

      Click here

  16. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. B006J8AC01
      *1 Fuel Suction Plate Sub-assembly
      *2 Tube Joint Clip
      *3 Fuel Tank Main Tube Sub-assembly
      *a Fuel Tube Joint
      *b O-ring
      *c Nylon Tube
      B006IR6 Pull off
      B006IKP Pull off

      Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

      Note


      • Remove any foreign matter on the fuel tube joint before performing this work.

      • Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

      • Be sure to disconnect the fuel tube joint by hand.

      • Do not bend, twist, pinch or kink the nylon tube.

      • Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

      • If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.

  17. REMOVE FUEL PUMP GAUGE RETAINER


    1. B006HHQC01
      B006IR6 Front Side

      Disengage the claw to remove the No. 1 fuel tube clamp.

    2. Remove the fuel pump gauge retainer.


      1. B006HVNC01
        *a Insertion Point
        *b SST (Plate)
        *c SST (Claw)
        *d SST (Bolt)

        Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

        SST
        09808-14031   ( 09808-01030, 09808-01050 )
        09808-01110

        Tech Tips

        Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.

      2. While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).

      3. B006IVEC01
        *a SST (Handle)
        *b SST (Plate)
        *c SST (Claw)
        *d SST (Bolt)
        *e Extension Bar (270 mm)

        Install SST (handle) and an extension bar (270 mm) to SST (plate).

        SST
        09808-14031   ( 09808-01010, 09808-01020 )

      4. Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

        Note


        • Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank assembly.

        • Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

        • Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

        • Do not spin SST too fast or use an impact wrench as this may result in damage to components.

        • If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

      5. While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.

  18. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


    1. Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

      Note

      Be careful not to bend the arm of the fuel sender gauge assembly.

    2. B006J53

      Remove the fuel suction tube set gasket from the fuel tank assembly.