ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *A | except Rough Road Area Specification Vehicles | *B | for Rough Road Area Specification Vehicles |
| *1 | INLET NO. 2 AIR CLEANER | *2 | INLET NO. 1 AIR CLEANER |
| *3 | NO. 1 ENGINE UNDER COVER ASSEMBLY | *4 | NO. 2 ENGINE UNDER COVER |
| *5 | REAR ENGINE UNDER COVER LH | *6 | REAR ENGINE UNDER COVER RH |
| *7 | RADIATOR SUPPORT OPENING COVER | *8 | NO. 1 ENGINE COVER SUB-ASSEMBLY |
| *9 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *10 | AIR CLEANER CASE SUB-ASSEMBLY |
| *11 | AIR CLEANER BRACKET | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | NO. 8 WATER BY-PASS HOSE | *2 | FUEL PIPE |
| *3 | OUTLET HEATER WATER HOSE E | *4 | FUEL TUBE SUB-ASSEMBLY |
| *5 | NO. 1 FUEL VAPOR FEED HOSE | *6 | NO. 3 RADIATOR HOSE |
| *7 | NO. 2 RADIATOR HOSE | *8 | OUTLET NO. 1 HYBRID WATER PUMP HOSE |
| *9 | INLET HYBRID RADIATOR HOSE | *10 | NO. 1 FUEL PIPE CLAMP |
| *11 | INLET HEATER WATER HOSE A | *12 | NO. 3 ENGINE WIRE |
| *13 | OUTLET NO. 1 OIL COOLER HOSE | *14 | INLET NO. 1 OIL COOLER HOSE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FRONT FLOOR COVER LH | *2 | FRONT FLOOR COVER RH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) | *2 | COLUMN HOLE COVER SILENCER SHEET |
| *3 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | *4 | FRONT SPEED SENSOR LH |
| *5 | TIE ROD END SUB-ASSEMBLY LH | *6 | FRONT AXLE SHAFT NUT LH |
| *7 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH | *8 | FRONT STABILIZER LINK ASSEMBLY LH |
| *9 | FRONT CENTER FLOOR BRACE | *10 | OUTLET HEATER WATER HOSE B |
| *11 | EXHAUST PIPE GASKET | *12 | COMPRESSION SPRING |
| *13 | COTTER PIN | *14 | EXHAUST PIPE SUPPORT |
| *15 | OUTLET HEATER WATER HOSE C | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Do not apply lubricants to the threaded parts |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | COMPRESSOR WITH MOTOR ASSEMBLY | *2 | BRACKET |
| *3 | STUD BOLT | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | except Rough Road Area Specification Vehicles | *B | for Rough Road Area Specification Vehicles |
| *1 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH | *2 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH |
| *3 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY | *4 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | w/ Canister Pump Module | *B | w/o Canister Pump Module |
| *1 | ENGINE MOUNTING INSULATOR LH | *2 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
| *3 | ENGINE WIRE | *4 | AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
| *5 | ENGINE ASSEMBLY WITH TRANSAXLE | *6 | WIRING HARNESS CLAMP BRACKET |
| *7 | COOLER BRACKET | *8 | NO. 2 EARTH WIRE |
| *9 | NO. 2 ENGINE MOUNTING STAY LH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque |  |
Adhesive 1324 |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | ENGINE ASSEMBLY | *2 | STARTER HOLE INSULATOR |
| *3 | TRANSMISSION INPUT DAMPER ASSEMBLY | *4 | FLYWHEEL SUB-ASSEMBLY |
| *5 | ONE-WAY CLUTCH HOLDING PLATE | *6 | FRONT DRIVE SHAFT HOLE SNAP RING |
| *7 | FRONT DRIVE SHAFT ASSEMBLY LH | *8 | FRONT DRIVE SHAFT ASSEMBLY RH |
| *9 | HYBRID VEHICLE TRANSAXLE ASSEMBLY | *10 | ONE-WAY CLUTCH ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1324 |  |
ATF WS |
| |
Do not apply lubricants to the threaded parts | ★ | Precoated part |
| *T1 | 1st: 49 (500, 36) 2nd: Turn 90° |
- | - |