INVERTER WITH CONVERTER COMPONENTS
ILLUSTRATION
| *1 | NO. 4 HV BATTERY SHIELD PANEL | *2 | SERVICE PLUG GRIP |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | COWL BODY MOUNTING REINFORCEMENT LH | *2 | NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL |
| *3 | OUTER COWL TOP PANEL SUB-ASSEMBLY | *4 | WATER GUARD PLATE |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | COWL BODY MOUNTING REINFORCEMENT LH | *2 | NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL |
| *3 | OUTER COWL TOP PANEL SUB-ASSEMBLY | *4 | WATER GUARD PLATE |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | except Rough Road Area Specification Vehicles | *B | for Rough Road Area Specification Vehicles |
| *1 | NO. 1 ENGINE COVER SUB-ASSEMBLY | *2 | BATTERY CLAMP SUB-ASSEMBLY |
| *3 | REAR ENGINE UNDER COVER LH | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *A | w/o Canister Pump Module | - | - |
| *1 | ENGINE WIRE | *2 | NO. 1 RELAY BLOCK COVER |
| *3 | CONNECTOR COVER ASSEMBLY | *4 | AIR CONDITIONING WIRE |
| *5 | HV FLOOR UNDER WIRE | *6 | WIRE HARNESS CLAMP BRACKET |
| *7 | NO. 3 ENGINE WIRE | *8 | OUTLET NO. 1 INVERTER COOLING HOSE |
| *9 | INLET NO. 1 INVERTER COOLING HOSE | *10 | INVERTER COVER |
| *11 | MOTOR CABLE | *12 | INVERTER WITH CONVERTER ASSEMBLY |
| *13 | INVERTER PROTECTOR | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | w/ Canister Pump Module | - | - |
| *1 | ENGINE WIRE | *2 | NO. 1 RELAY BLOCK COVER |
| *3 | CONNECTOR COVER ASSEMBLY | *4 | AIR CONDITIONING WIRE |
| *5 | HV FLOOR UNDER WIRE | *6 | WIRE HARNESS CLAMP BRACKET |
| *7 | NO. 3 ENGINE WIRE | *8 | OUTLET NO. 1 INVERTER COOLING HOSE |
| *9 | INLET NO. 1 INVERTER COOLING HOSE | *10 | INVERTER COVER |
| *11 | MOTOR CABLE | *12 | INVERTER WITH CONVERTER ASSEMBLY |
| *13 | INVERTER PROTECTOR | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | w/o Canister Pump Module | - | - |
| *1 | WIRE HARNESS CLAMP BRACKET | *2 | INVERTER WITH CONVERTER ASSEMBLY |
| *3 | NO. 1 INVERTER BRACKET | *4 | NO. 2 INVERTER BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/ Canister Pump Module | - | - |
| *1 | WIRE HARNESS CLAMP BRACKET | *2 | INVERTER WITH CONVERTER ASSEMBLY |
| *3 | NO. 1 INVERTER BRACKET | *4 | NO. 2 INVERTER BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |