CHARGE INLET INSTALLATION

PROCEDURE


  1. INSTALL CABLE EV CHARGER LOCK ASSEMBLY (w/ CABLE EV CHARGER LOCK ASSEMBLY)


    1. Install the cable EV charger lock assembly to the inlet AC charger cable with the pin.

  2. INSTALL INLET AC CHARGER CABLE (w/ CABLE EV CHARGER LOCK ASSEMBLY)

    CAUTION:

    Wear insulated gloves.


    1. A003MQXC01
      *A for Type A
      *B for Type B
      *a Earth Terminal
      B006IR6 Nut
      B006IKP Bolt

      Install the inlet AC charger cable with the 4 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Install the bolt to connect the earth terminal.

      Torque:
      for Type A
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      for Type B
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    3. Connect the cable EV charger lock assembly connector.

    4. A003MOEC01
      *a Green-colored Lock
      B006IEN Slide

      Engage the 4 clamps.

    5. Connect the inlet AC charger cable connector (B) and slide the green-colored lock as shown in the illustration to lock it securely.

      Note

      Make sure that the connector is connected securely.

    6. Connect the inlet AC charger cable connector (A).

    7. Connect the drain hose.

  3. INSTALL INLET AC CHARGER CABLE (w/o CABLE EV CHARGER LOCK ASSEMBLY)

    CAUTION:

    Wear insulated gloves.


    1. A003OQ2C01
      *A for Type A
      *B for Type B
      *a Earth Terminal
      B006IR6 Nut
      B006IKP Bolt

      Install the inlet AC charger cable with the 4 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Install the bolt to connect the earth terminal.

      Torque:
      for Type A
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      for Type B
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }
    3. A003MOEC01
      *a Green-colored Lock
      B006IEN Slide

      Engage the 4 clamps.

    4. Connect the inlet AC charger cable connector (B) and slide the green-colored lock as shown in the illustration to lock it securely.

      Note

      Make sure that the connectors are connected securely.

    5. Connect the inlet AC charger cable connector (A).

    6. Connect the drain hose.

  4. INSTALL NO. 2 HYBRID BATTERY INTAKE DUCT (for RH Side)

    Click here

  5. INSTALL NO. 1 HYBRID BATTERY INTAKE DUCT (for RH Side)

    Click here

  6. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

    Click here

  7. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  8. INSTALL TONNEAU COVER HOOK A (for RH Side with Toyota Safety Sense)

    Click here

  9. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (for RH Side with Toyota Safety Sense)

    Click here

  10. INSTALL NO. 2 ROPE HOOK (for RH Side without Toyota Safety Sense)

    Click here

  11. INSTALL ROPE HOOK (for RH Side without Toyota Safety Sense)

    Click here

  12. INSTALL REAR SEAT SIDE GARNISH RH

    Click here

  13. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH

    Click here

  14. INSTALL REAR UNDER SIDE COVER RH

    Click here

  15. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Click here

  16. INSTALL REAR DOOR SCUFF PLATE RH

    Click here

  17. INSTALL REAR SEAT CUSHION LOCK HOOK

    Click here

  18. INSTALL REAR SEAT CUSHION ASSEMBLY RH

    Click here

  19. INSTALL REAR SEATBACK ASSEMBLY RH

    Click here

  20. INSTALL REAR SEATBACK HINGE COVER

    Click here

  21. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)

    Click here

  22. INSTALL REAR DECK TRIM COVER

    Click here

  23. INSTALL DECK TRIM SERVICE HOLE COVER

    Click here

  24. INSTALL DECK FLOOR BOX LH

    Click here

  25. INSTALL DECK FLOOR BOX RH

    Click here

  26. INSTALL REAR NO. 4 FLOOR BOARD

    Click here

  27. INSTALL REAR NO. 3 FLOOR BOARD

    Click here

  28. INSTALL TONNEAU COVER ASSEMBLY

    Click here

  29. INSTALL SERVICE PLUG GRIP

    Click here