HYBRID BATTERY SYSTEM, Diagnostic DTC:P310362

DTC Code DTC Name
P310362 Hybrid/EV Battery Air Temperature Sensor "A"/"B" Signal Compare Failure

DESCRIPTION

Refer to the description for DTC P0AAC11.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P310362 Hybrid/EV Battery Air Temperature Sensor "A"/"B" Signal Compare Failure

The difference between the values of the two inlet air temperature sensor (thermistor) is above the specification.

(1 trip detection logic)

  • No. 3 HV supply stack sub-assembly

  • No. 4 HV supply stack sub-assembly

  • Battery ECU assembly

  • Wire harness or connector

 Comes on

Master Warning Light:

Comes on
Related Data List
DTC No. Data List
P310362

  • Hybrid Battery Cooling Fan Intake Air Temperature 1

  • Hybrid Battery Cooling Fan Intake Air Temperature 2

  • Hybrid Battery Cooling Fan Intake Air Temperature Sensor Voltage 1

  • Hybrid Battery Cooling Fan Intake Air Temperature Sensor Voltage 2

CONFIRMATION DRIVING PATTERN

Tech Tips

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the power switch off and wait for 35 minutes or more.

  5. Turn the power switch on (IG) and turn the GTS on.

  6. With power switch on (IG) and wait for 30 seconds or more.

  7. Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

  8. Check the DTC judgment result.

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AAC11.

Click here

CAUTION / NOTICE / HINT

CAUTION:


  • B006HUP

    Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.


    • Inspecting the high-voltage system

    • Disconnecting the low voltage connector of the inverter with converter assembly

    • Disconnecting the low voltage connector of the HV battery

    • Disconnecting the low voltage connector of the electric vehicle charger assembly

    • Disconnecting the low voltage connector of the solar energy control unit

  • B006IQP

    To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

  • B006HQC

    After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • B006IVPC02
    *a Without waiting for 10 minutes

    After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.

  • Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

    If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

  • B006I3VC06
    *a Dealer
    *b Battery Collection Agent

    When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.


    • Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.

  • Before returning the HV battery, make sure to perform a recovery inspection.

    Click here

  • Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

    Click here

  • Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

  • B006IGA

    After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

PROCEDURE


  1. CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.

    4. Check for DTCs.


      Powertrain > HV Battery > Trouble Codes
      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      "P310362" only is output, or DTCs except the ones in the table below are also output. A
      DTCs of hybrid battery system in the table below are output. B
      DTCs of hybrid control system in the table below are output. C
      System Relevant DTC
      Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
      P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
      P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
      Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation

    5. Turn the power switch off.


    B

    GO TO DTC CHART (HYBRID BATTERY SYSTEM) Click here

    C

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    A

  2. CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY)

    Result
    Result
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the upper hybrid battery cover sub-assembly.

      Click here

    3. B006J82N04

      Check the connections of the t14 battery ECU assembly connector.

      Click here

      OK
      The connector is connected securely and there are no contact problems.

    4. Install the upper hybrid battery cover sub-assembly.

      Result
      Proceed to
      OK
      NG

    NG

    CONNECT SECURELY

    OK

  3. CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR 0

    Result
    Result Proceed to
    The inlet air temperature sensor 0 is installed in the correct location and its claws are engaged securely. A
    The claws of the inlet air temperature sensor 0 are damaged. B
    The inlet air temperature sensor 0 is not installed correctly, but its claws are not damaged. C

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the No. 3 hybrid battery intake duct (for RH side).

      Click here

    3. B006J0I

      Visually check the installation condition of the inlet air temperature sensor 0.

      Result
      Result Proceed to
      The inlet air temperature sensor 0 is installed in the correct location and its claws are engaged securely. A
      The claws of the inlet air temperature sensor 0 are damaged. B
      The inlet air temperature sensor 0 is not installed correctly, but its claws are not damaged. C

    4. Install the No. 3 hybrid battery intake duct (for RH side).


    B

    REPLACE NO. 3 HV SUPPLY STACK SUB-ASSEMBLY Click here

    C

    INSTALL PARTS CORRECTLY

    A

  4. CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR 1

    Result
    Result Proceed to
    The inlet air temperature sensor 1 is installed in the correct location and its claws are engaged securely. A
    The claws of the inlet air temperature sensor 1 are damaged. B
    The inlet air temperature sensor 1 is not installed correctly, but its claws are not damaged. C

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the No. 3 hybrid battery intake duct (for LH side).

      Click here

    3. B006HSA

      Visually check the installation condition of the inlet air temperature sensor 1.

      Result
      Result Proceed to
      The inlet air temperature sensor 1 is installed in the correct location and its claws are engaged securely. A
      The claws of the inlet air temperature sensor 1 are damaged. B
      The inlet air temperature sensor 1 is not installed correctly, but its claws are not damaged. C

    4. Install the No. 3 hybrid battery intake duct (for LH side).


    B

    REPLACE NO. 4 HV SUPPLY STACK SUB-ASSEMBLY Click here

    C

    INSTALL PARTS CORRECTLY

    A

  5. CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR 0)

    Result
    Proceed to
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the upper hybrid battery cover sub-assembly.

      Click here

    3. B006J82N02

      Disconnect the t14 battery ECU assembly connector.

      Note

      Before disconnecting the connector, check that it is not loose or disconnected.

    4. B006I6MC39
      *a

      Front view of wire harness connector

      (to Battery ECU Assembly)

      Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      t14-60 (TC0) - t14-37 (GC0)

      Power switch off

      0 to 10°C (32 to 50°F)

      		 17.7 to 27.8 kΩ
      t14-60 (TC0) - t14-37 (GC0)

      Power switch off

      10 to 20°C (50 to 68°F)

      		 12.0 to 18.2 kΩ
      t14-60 (TC0) - t14-37 (GC0)

      Power switch off

      20 to 30°C (68 to 86°F)

      		 8.22 to 12.2 kΩ
      t14-60 (TC0) - t14-37 (GC0)

      Power switch off

      30 to 40°C (86 to 104°F)

      		 5.74 to 8.41 kΩ
      t14-60 (TC0) - t14-37 (GC0)

      Power switch off

      40 to 50°C (104 to 122°F)

      		 4.09 to 5.91 kΩ

      Note

      When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

    5. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      t14-60 (TC0) - Body ground and other terminals Power switch off 10 kΩ or higher
      t14-37 (GC0) - Body ground and other terminals Power switch off 10 kΩ or higher

    6. Connect the cable to the negative (-) auxiliary battery terminal.

    7. Turn the power switch on (IG).

    8. Measure the voltage according to the value (s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      t14-60 (TC0) - Body ground Power switch on (IG) Below 1 V

      Note


      • Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      • If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

    11. Reconnect the t14 battery ECU assembly connector.

    12. Install the upper hybrid battery cover sub-assembly.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 3 HV SUPPLY STACK SUB-ASSEMBLY) Click here

    OK

  6. CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR 1)

    Result
    Proceed to
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the upper hybrid battery cover sub-assembly.

      Click here

    3. B006J82N02

      Disconnect the t14 battery ECU assembly connector.

      Note

      Before disconnecting the connector, check that it is not loose or disconnected.

    4. B006I6MC40
      *a

      FRONT view of wire harness connector

      (to Battery ECU Assembly)

      Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      t14-62 (TC1) - t14-61 (GC1)

      Power switch off

      0 to 10°C (32 to 50°F)

      		 17.7 to 27.8 kΩ
      t14-62 (TC1) - t14-61 (GC1)

      Power switch off

      10 to 20°C (50 to 68°F)

      		 12.0 to 18.2 kΩ
      t14-62 (TC1) - t14-61 (GC1)

      Power switch off

      20 to 30°C (68 to 86°F)

      		 8.22 to 12.2 kΩ
      t14-62 (TC1) - t14-61 (GC1)

      Power switch off

      30 to 40°C (86 to 104°F)

      		 5.74 to 8.41 kΩ
      t14-62 (TC1) - t14-61 (GC1)

      Power switch off

      40 to 50°C (104 to 122°F)

      		 4.09 to 5.91 kΩ

      Note

      When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

    5. Measure the resistance according to the value (s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      t14-62 (TC1) - Body ground and other terminals Power switch off 10 kΩ or higher
      t14-61 (GC1) - Body ground and other terminals Power switch off 10 kΩ or higher

    6. Connect the cable to the negative (-) auxiliary battery terminal.

    7. Turn the power switch on (IG).

    8. Measure the voltage according to the value (s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      t14-62 (TC1) - Body ground Power switch on (IG) Below 1 V

      Note


      • Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      • If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.

    9. Turn the power switch off.

    10. Disconnect the cable from the negative (-) auxiliary battery terminal.

    11. Reconnect the t14 battery ECU assembly connector.

    12. Install the upper hybrid battery cover sub-assembly.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE BATTERY ECU ASSEMBLY Click here

    NG

  7. CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 4 HV SUPPLY STACK SUB-ASSEMBLY)

    Result
    Proceed to
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the upper hybrid battery cover sub-assembly.

      Click here

    3. B006J82N02

      Disconnect the t14 battery ECU assembly connector.

      Note

      Before disconnecting the connector, check that it is not loose or disconnected.

    4. Remove the No. 2 battery frame.

      Click here

    5. B006J1SN03

      Disconnect the t12 No. 4 HV supply stack sub-assembly connector.

      Note

      Before disconnecting the connector, check that it is not loose or disconnected.

    6. B006IHHC05
      *a

      Front view of wire harness connector

      (to Battery ECU Assembly)
      *b

      Front view of wire harness connector

      (to No. 4 HV supply stack sub-assembly)

      Measure the resistance according to the value(s) in the tables below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      t12-1 (TC1) - t14-62 (TC1) Power switch off Below 1 Ω
      t12-5 (GC1) - t14-61 (GC1) Power switch off Below 1 Ω
      t12-1 (TC1) or t14-62 (TC1) - Body ground and other terminals Power switch off 10 kΩ or higher
      t12-5 (GC1) or t14-61 (GC1) - Body ground and other terminals Power switch off 10 kΩ or higher

    7. Connect the cable to the negative (-) auxiliary battery terminal.

    8. Turn the power switch on (IG).

    9. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      t12-1 (TC1) or t14-62 (TC1) - Body ground Power switch on (IG) Below 1 V

      Note


      • Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      • If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.

    10. Turn the power switch off.

    11. Disconnect the cable from the negative (-) auxiliary battery terminal.

    12. Reconnect the t12 No. 4 HV supply stack sub-assembly connector.

    13. Install the No. 2 battery flame.

    14. Reconnect the t14 battery ECU assembly connector.

    15. Install the upper hybrid battery cover sub-assembly.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 4 HV SUPPLY STACK SUB-ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 3 HV SUPPLY STACK SUB-ASSEMBLY)

    Result
    Proceed to
    OK
    NG

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Remove the upper hybrid battery cover sub-assembly.

      Click here

    3. B006J82N02

      Disconnect the t14 battery ECU assembly connector.

      Note

      Before disconnecting the connector, check that it is not loose or disconnected.

    4. Remove the No. 2 battery frame.

      Click here

    5. B006H99N01

      Disconnect the t11 No. 3 HV supply stack sub-assembly connector.

      Note

      Before disconnecting the connector, check that it is not loose or disconnected.

    6. B006HU3C05
      *a

      Front view of wire harness connector

      (to Battery ECU Assembly)
      *b

      Front view of wire harness connector

      (to No. 3 HV supply stack sub-assembly)

      Measure the resistance according to the value(s) in the tables below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      t11-2 (TC0) - t14-60 (TC0) Power switch off Below 1 Ω
      t11-7 (GC0) - t14-37 (GC0) Power switch off Below 1 Ω
      t11-2 (TC0) or t14-60 (TC0) - Body ground and other terminals Power switch off 10 kΩ or higher
      t11-7 (GC0) or t14-37 (GC0) - Body ground and other terminals Power switch off 10 kΩ or higher

    7. Connect the cable to the negative (-) auxiliary battery terminal.

    8. Turn the power switch on (IG).

    9. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      t11-2 (TC0) or t14-60 (TC0) - Body ground Power switch on (IG) Below 1 V

      Note


      • Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      • If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.

    10. Turn the power switch off.

    11. Disconnect the cable from the negative (-) auxiliary battery terminal.

    12. Reconnect the t11 No. 3 HV supply stack sub-assembly connector.

    13. Install the No. 2 battery flame.

    14. Reconnect the t14 battery ECU assembly connector.

    15. Install the upper hybrid battery cover sub-assembly.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 3 HV SUPPLY STACK SUB-ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR