SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P05A27E, P05A27F

DTC Code DTC Name
P05A27E Active Grille Air Shutter "A" Actuator Stuck On
P05A27F Active Grille Air Shutter "A" Actuator Stuck Off

DESCRIPTION

Refer to DTC P059F73.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P05A27E Active Grille Air Shutter "A" Actuator Stuck On

The following condition is met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):


  • Grille shutter opening operation is performed for 11 seconds or more and the ECM receives a malfunction signal once or more.

  • Radiator shutter sub-assembly

  • Swing grille actuator assembly

 Does not come on DTC stored SAE Code: P05A3
P05A27F Active Grille Air Shutter "A" Actuator Stuck Off

The following condition is met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):


  • Grille shutter closing operation is performed for 11 seconds or more and the ECM receives a malfunction signal once or more.

  • Radiator shutter sub-assembly

  • Swing grille actuator assembly

 Does not come on DTC stored SAE Code: P05A3

Tech Tips

*: For every 65 ms that the ECM receives a grille shutter system malfunction signal from the grille shutter ECU (swing grille actuator assembly) the ECM determines it has received the signal 1 time. If the ECM determines the malfunction signal has been received 17 consecutive times (the signal is received for approximately 1 second continuously), it will store a DTC.

MONITOR DESCRIPTION

If the grille shutter ECU (swing grille actuator assembly) detects that the grille shutter motor (swing grille actuator assembly) is performing an open or close operation for longer than the threshold, it will output a malfunction signal to the ECM and the ECM will store a DTC.

Detection Condition DTC No.
Opening Operation P05A27E (Active Grille Air Shutter "A" Actuator Stuck On)
Closing Operation P05A27F (Active Grille Air Shutter "A" Actuator Stuck Off)

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the power switch off and wait for at least 30 seconds.

  6. Turn the power switch on (IG).

  7. Turn the GTS on.

  8. Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

  9. According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

    OK
    "Normal" is displayed.

  10. Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

  11. According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

    OK
    "Normal" is displayed.

CAUTION / NOTICE / HINT

Note

In order to ensure safety, before performing troubleshooting or removing the swing grille actuator assembly or radiator shutter sub-assembly, change the grille shutter control mode to maintenance mode.

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.


      Body Electrical > Grill Shutter > Utility
      Tester Display
      Grill Shutter Control Mode Switching

    5. According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

      Result
      Proceed to
      NEXT

    NEXT

  2. INSPECT GRILLE SHUTTER (FOREIGN MATTER AND ICE)


    1. Check the area around the shutters and the links of the grille shutter for foreign matter and ice.

      OK
      No foreign matter or ice.
      Result
      Proceed to
      OK
      NG

    NG

    REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER) Click here

    OK

  3. PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.


      Body Electrical > Grill Shutter > Active Test
      Active Test Display
      Shutter Closing Operation Lock Detection
      Data List Display
      Shutter Operation Lock Detection Result for Active Test

    5. According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

      OK
      "Normal" is displayed.

    6. Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.


      Body Electrical > Grill Shutter > Active Test
      Active Test Display
      Shutter Opening Operation Lock Detection
      Data List Display
      Shutter Operation Lock Detection Result for Active Test

    7. According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

      OK
      "Normal" is displayed.

      Tech Tips

      When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the grille shutter system has returned to normal.

      Result
      Proceed to
      OK
      NG

    NG

    PERFORM ACTIVE TEST USING GTS (SWING GRILLE ACTUATOR ASSEMBLY OPERATION) Click here

    OK

  4. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    6. Turn the power switch off and wait for at least 30 seconds.

      Result
      Proceed to
      NEXT

    NEXT

  5. PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.


      Body Electrical > Grill Shutter > Utility
      Tester Display
      Grill Shutter Control Mode Switching

    5. According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

    6. Check for DTCs and make sure that DTC B1333 is not output.


      Body Electrical > Grill Shutter > Trouble Codes
      Result
      Proceed to
      NEXT

    NEXT

    END

  6. PERFORM ACTIVE TEST USING GTS (SWING GRILLE ACTUATOR ASSEMBLY OPERATION)


    1. Remove the radiator shutter sub-assembly.

      Click here

    2. Remove the swing grille actuator assembly.

      Click here

    3. Reconnect the swing grille actuator assembly connector.

    4. Connect the GTS to the DLC3.

    5. Turn the power switch on (IG).

    6. Turn the GTS on.

    7. Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection.


      Body Electrical > Grill Shutter > Active Test
      Tester Display
      Shutter Closing Operation Lock Detection

    8. According to the display on the GTS, perform the Active Test and check the operation of the swing grille actuator assembly.

      OK
      Operation is normal.

    9. Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection.


      Body Electrical > Grill Shutter > Active Test
      Tester Display
      Shutter Opening Operation Lock Detection

    10. According to the display on the GTS, perform the Active Test and check the operation of the swing grille actuator assembly.

      OK
      Operation is normal.

      Tech Tips

      Perform "Grill Shutter Control Mode Switching and Grill Shutter Initialization" after replacing the swing grille actuator assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SWING GRILLE ACTUATOR ASSEMBLY Click here

    OK

  7. INSPECT RADIATOR SHUTTER SUB-ASSEMBLY (GRILLE SHUTTER OPERATION)


    1. Remove the radiator shutter sub-assembly.

      Click here

    2. Remove the swing grille actuator assembly.

      Click here

    3. Manually open and close the radiator shutter sub-assembly and check that it moves smoothly.

      OK
      Radiator shutter sub-assembly moves smoothly.

      Tech Tips

      Perform "Grill Shutter Control Mode Switching and Grill Shutter Initialization" after replacing the swing grille actuator assembly or radiator shutter sub-assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SWING GRILLE ACTUATOR ASSEMBLY Click here

    NG

    REPLACE RADIATOR SHUTTER SUB-ASSEMBLY Click here

  8. REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)


    1. Remove any foreign matter and/or ice from the area around the shutters and the links of the grille shutter.

      Result
      Proceed to
      NEXT

    NEXT

  9. PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.


      Body Electrical > Grill Shutter > Active Test
      Active Test Display
      Shutter Closing Operation Lock Detection
      Data List Display
      Shutter Operation Lock Detection Result for Active Test

    5. According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

      OK
      "Normal" is displayed.

    6. Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.


      Body Electrical > Grill Shutter > Active Test
      Active Test Display
      Shutter Opening Operation Lock Detection
      Data List Display
      Shutter Operation Lock Detection Result for Active Test

    7. According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

      OK
      "Normal" is displayed.

      Tech Tips

      When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the grille shutter system has returned to normal.

      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 6 Click here

    OK

  10. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    6. Turn the power switch off and wait for at least 30 seconds.

      Result
      Proceed to
      NEXT

    NEXT

  11. PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.


      Body Electrical > Grill Shutter > Utility
      Tester Display
      Grill Shutter Control Mode Switching

    5. According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

    6. Check for DTCs and make sure that DTC B1333 is not output.


      Body Electrical > Grill Shutter > Trouble Codes
      Result
      Proceed to
      NEXT

    NEXT

    END