REAR DOOR WINDOW FRAME MOULDING REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door belt moulding assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

  • Rear door glass

  • Rear door glass run

 Initialize power window control system

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

    Click here

  2. REMOVE REAR SPEAKER ASSEMBLY

    Click here

  3. REMOVE REAR DOOR FRAME GARNISH

    Click here

  4. REMOVE REAR DOOR CHECK ASSEMBLY

    Click here

  5. REMOVE REAR DOOR WEATHERSTRIP

    Click here

  6. REMOVE REAR DOOR WINDOW FRAME FRONT MOULDING


    1. Using an infrared light, heat the rear door window frame front moulding.

      Heating Temperature
      Item Temperature
      Door Frame 40 to 60°C (104 to 140°F)
      Rear Door Window Frame Front Moulding 20 to 30°C (68 to 86°F)

      CAUTION:

      A01MIK5C14
      *a Heated Part
      *b Infrared Light

      • Do not touch the infrared light and heated parts.

      • Touching the infrared light may result in burns.

      • Touching heated parts for a long time may result in burns.

    2. Using a moulding remover D, disengage the clip and guide to remove the rear door window frame front moulding as shown in the illustration.

      A01MK22C02
      *a Double-sided Tape *b Caulking Sponge with Butyl Layer
      B006JFV Remove in this Direction (1) B006JHL Remove in this Direction (2)

  7. REMOVE REAR DOOR WINDOW FRAME UPPER MOULDING


    1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

      A01MJECC02
      *a 5.0 mm (0.197 in.) - -

    2. Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Tech Tips

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 4 rivets.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

      • Be careful of the drilled rivets, as they may be hot.

    4. Remove the front end cover, rear end cover and rear door window frame upper moulding.

  8. REMOVE REAR DOOR WINDOW FRAME REAR MOULDING


    1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

      A01MGQGC02
      *a 5.0 mm (0.197 in.) - -

    2. Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Tech Tips

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 3 rivets.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

      • Be careful of the drilled rivets, as they may be hot.

    4. Remove the upper end cover and rear door window frame rear moulding.