REAR BUMPER REASSEMBLY

PROCEDURE


  1. INSTALL REAR BUMPER SIDE SUPPORT LH


    1. A01MFT2C02
      B006JFV Install in this Direction

      Engage the guides to install the rear bumper side support LH as shown in the illustration.

  2. INSTALL REAR BUMPER SIDE SUPPORT RH

    Tech Tips

    Use the same procedure as for the LH side.

  3. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH

    Click here

  4. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  5. INSTALL REAR COMBINATION LIGHT COVER LH

    Click here

  6. INSTALL REAR COMBINATION LIGHT COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  7. INSTALL REAR BUMPER SIDE RETAINER LH


    1. A01MIG5C02
      B006JFV Install in this Direction

      Engage the claws to install the rear bumper side retainer LH as shown in the illustration.

      Tech Tips

      Do not forcibly engage the clip.

    2. A01MJS1

      Install the 2 clips as shown in the illustration.

  8. INSTALL REAR BUMPER SIDE RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  9. INSTALL REAR BUMPER ARM SUB-ASSEMBLY LH


    1. A01MGYP

      Install the rear bumper arm sub-assembly LH with the 3 bolts.

      Torque:
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }

  10. INSTALL REAR BUMPER ARM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  11. INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY


    1. Install the rear bumper reinforcement sub-assembly with the 6 bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }
      A01MIMF

  12. INSTALL REAR BUMPER PROTECTOR


    1. A01MG8K

      Engage the claw to install the rear bumper protector.

    2. Install the 2 screws.

      Tech Tips

      Use the same procedure for the RH side.

  13. INSTALL REAR BUMPER ENERGY ABSORBER


    1. Using a piece of cloth, rub off any double-side tape that remains on the rear bumper protector.

      Note


      • Installing the rear bumper energy absorber while old double-sided tape remains can cause adhesion failure.

      • Using a screwdriver or similar tool to remove the old tape can damage the surface and cause adhesion failure.

    2. Using a non-residue solvent, clean the attachment surface.

    3. Remove the peeling paper on a new rear bumper energy absorber.

    4. A01MIODC02
      B000ZUW Double-sided Tape
      B006JFV Install in this Direction

      Engage the guides to install the rear bumper energy absorber as shown in the illustration.

      Note

      Apply 2 pieces of double-sided type to the rear bumper energy absorber while pressing them into place.

  14. INSTALL REAR BUMPER PLATE LH


    1. A01MFYF

      Engage the hook.

    2. A01MJEUC02
      B006JFV Install in this Direction

      Engage the claws to install the rear bumper plate LH as shown in the illustration.

  15. INSTALL REAR BUMPER PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  16. INSTALL CENTER REAR BUMPER BRACKET


    1. A01MGS6

      Install the center rear bumper bracket.

    2. Install the 4 outside moulding retainers.

  17. INSTALL REAR SIDE SPOILER SUB-ASSEMBLY LH


    1. A01MIEFC02
      B006JFV Install in this Direction

      Engage the claws to install the rear side spoiler sub-assembly LH as shown in the illustration.

    2. A01MGPE

      Install the 6 outside moulding retainers.

    3. Install the 3 screws.

  18. INSTALL REAR SIDE SPOILER SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  19. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER

    Click here

  20. INSTALL NO. 2 ULTRASONIC SENSOR

    Click here

  21. INSTALL NO. 3 LUGGAGE ROOM WIRE


    1. Engage the clamps to install the No. 3 luggage room wire.

      A01MJ2L

    2. Connect the 4 connectors.

  22. INSTALL REAR FOG LIGHT ASSEMBLY


    1. A01MIR7C04
      B006JFV Install in this Direction

      Align the claws at the top of the rear fog light assembly, then engage the claws at the bottom of the rear fog light assembly as shown in the illustration to install the rear fog light assembly.

    2. A01MFXL

      Install the bracket A and bracket B with the 2 screws.

    3. A01MG25

      Connect the connector.