POWER MIRROR CONTROL SYSTEM AUTO Power Retract Mirrors do not operate

DESCRIPTION

When the outer mirror switch assembly is set to AUTO (neutral position), an AUTO signal is detected by the main body ECU (multiplex network body ECU). When locking and unlocking all doors with the power switch off, the main body ECU (multiplex network body ECU) sends deploy/retract signals to the outer mirror control ECU assembly via CAN communication. The outer mirror control ECU assembly deploys and retracts the outer rear view mirror assembly based on the received signals.

WIRING DIAGRAM

A01MHGRE01
A01MHGRE05

CAUTION / NOTICE / HINT

Note


  • First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

  • If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

PROCEDURE


  1. CHECK POWER RETRACT MIRROR FUNCTION


    1. Check power retract mirror function.

      Click here

      OK
      Power retract mirror function is normal.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO OTHER FLOWCHART (Power Retractable Mirrors do not Operate with Power Retract Mirror Switch) Click here

    OK

  2. CHECK ENTRY AND START SYSTEM (for Entry Function)


    1. Check the entry and start system (for Entry Function).

      Click here

      OK
      Entry and start system (for Entry Function) is normal.
      Result
      Proceed to
      OK
      NG

      Click here


    NG

    GO TO ENTRY AND START SYSTEM (for Entry Function) Click here

    OK

  3. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM


    1. Check the wireless door lock control system.

      Click here

      OK
      Wireless door lock control system is normal.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO WIRELESS DOOR LOCK CONTROL SYSTEM Click here

    OK

  4. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Auto Mirror SW Auto retractable outer mirror switch signal OFF or ON

      OFF: Auto retractable outer mirror switch off

      ON: Auto retractable outer mirror switch on

      		 -

      Body Electrical > Main Body > Data List
      Tester Display
      Auto Mirror SW
      OK
      On the GTS screen, ON or OFF is displayed for each item according to the table above.
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

  5. REPLACE OUTER MIRROR SWITCH ASSEMBLY (MIRROR RETRACTOR SWITCH)


    1. Replace the outer mirror switch assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK AUTO POWER RETRACT MIRROR FUNCTION


    1. Check the auto power retract mirror function.

      Click here

      OK
      Auto power retract mirror function operates normally.
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    A

    END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here