POWER WINDOW CONTROL SYSTEM Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH

DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.

If power window initialization has not been performed, the auto up and down function will not operate.

Click here

WIRING DIAGRAM

A01MFYLE01
*a Rear Power Window Regulator Switch Assembly (for Rear RH Door)
*b Rear Power Window Regulator Motor Assembly RH

CAUTION / NOTICE / HINT

Note


  • If the rear power window regulator motor assembly RH has been replaced with a new one, initialize the power window control system.

    Click here

  • Check that the "RR Window Auto Up" and "RR Window Auto Down" power window control system customize settings are "ON" before proceeding with work.

    Click here

  • After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.

Tech Tips

If the pulse sensor built into the rear power window regulator motor assembly RH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly (for rear RH door) at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly (for rear RH door).

Click here

PROCEDURE


  1. READ VALUE USING GTS (RR-DOOR MOTOR)


    1. Read the Data List according to the display on the GTS.

      Click here


      Body Electrical > RR-Door Motor > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      RR Door P/W Auto SW Rear RH door power window auto switch signal OFF or ON

      OFF: Rear RH door power window auto switch not being operated

      ON: Rear RH door power window auto switch being operated

      		 -

      Body Electrical > RR-Door Motor > Data List
      Tester Display
      RR Door P/W Auto SW
      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR) Click here

    OK

  2. PERFORM INITIALIZATION (FOR REAR RH DOOR)


    1. Initialize the rear power window regulator motor assembly RH.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  3. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)


    1. Check that the rear RH door power window moves when the auto up and down function of the rear power window regulator switch assembly (for rear RH door) is operated.

      Click here

      OK
      Rear RH door auto up and down function is normal.
      Result
      Proceed to
      OK
      NG

    OK

    END (PROBLEM DUE TO INITIALIZATION FAILURE)

    NG

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

  4. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR)


    1. Remove the rear power window regulator switch assembly (for rear RH door).

      Click here

    2. Inspect the rear power window regulator switch assembly (for rear RH door).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR) Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY [FOR REAR RH DOOR] - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the O1 rear power window regulator switch assembly (for rear RH door) connector.

    2. Disconnect the M1 rear power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O1-8 (AUTO) - M1-4 (AUTO) Always Below 1 Ω
      O1-8 (AUTO) or M1-4 (AUTO) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR