POWER WINDOW REGULATOR MOTOR(for Rear Side) INSPECTION

PROCEDURE


  1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Note


    • Do not apply voltage to any terminals except terminals 1 and 2 to avoid damaging the pulse sensor inside the motor.

    • Do not apply voltage to any terminals except terminals 1 and 2 to avoid damaging the pulse sensor inside the power window regulator motor assembly LH.


    1. A01MHTMC03
      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly LH)
      *b Counterclockwise
      *c Clockwise
      *d Motor Gear

      Check that the motor gear rotates smoothly as follows.

      Specified Condition
      Measurement Condition Specified Condition

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

      2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

      3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.

      		 Motor gear rotates counterclockwise (UP)

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

      2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

      3. After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.

      		 Motor gear rotates clockwise (DOWN)

      Tech Tips

      If the result is not as specified, replace the power window regulator motor assembly LH.

  2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    Note


    • Do not apply voltage to any terminals except terminals 1 and 2 to avoid damaging the pulse sensor inside the motor.

    • Do not apply voltage to any terminals except terminals 1 and 2 to avoid damaging the pulse sensor inside the power window regulator motor assembly RH.


    1. A01MI5BC03
      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly RH)
      *b Clockwise
      *c Counterclockwise
      *d Motor Gear

      Check that the motor gear rotates smoothly as follows.

      Specified Condition
      Measurement Condition Specified Condition

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

      2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

      3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.

      		 Motor gear rotates clockwise (UP)

      1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

      2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

      3. After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.

      		 Motor gear rotates counterclockwise (DOWN)

      Tech Tips

      If the result is not as specified, replace the power window regulator motor assembly RH.