AIR CONDITIONING SYSTEM, Diagnostic DTC:B1413/13

DTC Code DTC Name
B1413/13 Evaporator Temperature Sensor Circuit

DESCRIPTION

The No. 1 cooler thermistor is installed on the evaporator in the air conditioner unit to detect the temperature of the air that has passed through the evaporator and is used to control the air conditioning. It sends signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor changes. This sensor is used for frost prevention.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1413/13 Evaporator Temperature Sensor Circuit

Any of the following conditions is met:


  • Open in No. 1 cooler thermistor circuit

  • Short in No. 1 cooler thermistor circuit


  • No. 1 cooler thermistor

  • Air conditioning harness assembly

  • Air conditioning amplifier assembly

Memorized (4 seconds or more)

Tech Tips

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG)
Malfunction Status Open in No. 1 cooler thermistor circuit -
Short in No. 1 cooler thermistor circuit -
Detection Time 4 seconds or more 4 seconds or more
Number of Trips 1 trip 1 trip

Tech Tips

DTC will be output when conditions for either of the patterns in the table above are met.

WIRING DIAGRAM

A01MIAEE01

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Data List.

    5. Check the value(s) by referring to the table below.


      Body Electrical > Air Conditioner > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Evaporator Fin Thermistor No. 1 cooler thermistor

      Min.: -29.70°C (-21.46°F)

      Max.: 59.55°C (139.19°F)

      Actual evaporator temperature displayed -

      Body Electrical > Air Conditioner > Data List
      Tester Display
      Evaporator Fin Thermistor
      OK
      The display is as specified in the normal condition column.
      Result
      Result Proceed to
      OK (When troubleshooting according to Problem Symptoms Table) A
      OK (When troubleshooting according to the DTC) B
      NG C

    A
    B
    C
  2. INSPECT NO. 1 COOLER THERMISTOR


    1. Remove the No. 1 cooler thermistor.

      Click here

    2. Inspect the No. 1 cooler thermistor.

      Click here

      Result
      Proceed to
      OK
      NG

    NG
    OK
  3. CHECK AIR CONDITIONING HARNESS ASSEMBLY


    1. A01MJXWC03
      *1 Air Conditioning Harness Assembly
      *a

      Front view of air conditioning harness assembly

      (to Air Conditioning Amplifier Assembly)

      *b

      Front view of air conditioning harness assembly

      (to No. 1 cooler thermistor [evaporator temperature sensor])

      Disconnect the air conditioning harness assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z1-6 (TEA) - A-2 Always Below 1 Ω
      z1-5 (SGA) - A-1 Always Below 1 Ω
      z1-6 (TEA) or A-2 - Body ground Always 10 kΩ or higher
      z1-5 (SGA) or A-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK
    NG