SIDE AIRBAG SENSOR(for Center Pillar) INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL NO. 2 SIDE AIRBAG SENSOR ASSEMBLY

   
   

   1. Check that the power switch is off.

   2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      
      

      • 

        Wait at least 90 seconds after disconnecting the cable from negative (-) auxiliary battery terminal to disable the SRS system.

      • 

        If this procedure is performed without disconnecting the cable from negative (-) auxiliary battery terminal, the airbag may deploy even if an impact is applied only to the No. 2 side airbag sensor assembly. Therefore, make sure that the cable from negative (-) auxiliary battery terminal is disconnected before performing this procedure.

   3. Before connecting the airbag connector, check that the position of the housing lock is correct as shown in the illustration.

      

      *1	CPA	-	-
      *a	Incorrect	*b	Correct

   4. Engage the guide and hold the No. 2 side airbag sensor assembly in place.

   5. Install the bolt.

      Torque:

      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note

      
      

      • If the No. 2 side airbag sensor assembly has been dropped, replace it with a new one.

      • When installing the No. 2 side airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • Tighten the bolt while holding the No. 2 side airbag sensor assembly because the No. 2 side airbag sensor assembly guide is easily damaged.

   6. Connect the connector.

      
      

      1. While holding the CPA, be sure to engage the No. 2 side airbag sensor assembly connector until are locked and check that the CPA is in original position (when looking, make sure that a click sound can be heard).

         

         *a	Housing Lock	*b	CPA
         *c	CPA Upper Part	*d	Connection is Completed

         Note

         
         

         • When connecting any airbag connector, take care not to damage the airbag wire harness.

         • Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.

   7. Check that there is no looseness in the installation parts of the No. 2 side airbag sensor assembly.

2. INSTALL SIDE AIRBAG SENSOR ASSEMBLY

   
   

   1. Check that the power switch is off.

   2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      
      

      • 

        Wait at least 90 seconds after disconnecting the cable from negative (-) auxiliary battery terminal to disable the SRS system.

      • 

        If this procedure is performed without disconnecting the cable from negative (-) auxiliary battery terminal, the airbag may deploy even if an impact is applied only to the side airbag sensor assembly. Therefore, make sure that the cable from negative (-) auxiliary battery terminal is disconnected before performing this procedure.

   3. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      

      *a	Correct	*b	Incorrect
      *c	CPA	*d	Housing

   4. Engage the guide and hold the side airbag sensor assembly in place.

   5. Install the bolt.

      Torque:

      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note

      
      

      • If the side airbag sensor assembly has been dropped, replace it was with a new one.

      • When installing the side airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • Tighten the bolt while holding the side airbag sensor assembly because the side airbag sensor assembly guide is easily damaged.

   6. Connect the connector.

      
      

      1. While holding the CPA, be sure to engage the connectors until they are locked and check that the CPA is in its original position (When locking, make sure that a click sound can be heard.)

         

         *1	CPA	-	-
         *a	Slide	-	-

         Note

         
         

         • When connecting any connector, take care not to damage the wire harness.

         • Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.

   7. Check that there is no looseness in the installation parts of the side airbag assembly .

3. INSTALL CENTER PILLAR LOWER GARNISH

   Click here

4. CONNECT FRONT SEAT OUTER BELT ASSEMBLY

   Click here

5. INSTALL LAP BELT OUTER ANCHOR COVER

   Click here

6. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

   Click here

7. INSTALL REAR DOOR SCUFF PLATE

   Click here

8. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

   Click here

9. INSTALL FRONT DOOR SCUFF PLATE

   Click here

10. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    
    

    1. Connect the cable to the negative (-) auxiliary battery terminal.

       Click here

11. INSTALL LUGGAGE TRIM SERVICE HOLE COVER

    Click here

12. INSPECT SRS WARNING LIGHT

    Click here

13. FC STACK ASSEMBLY ON-VEHICLE INSPECTION

    Click here

    Tech Tips

    Perform an on-vehicle inspection of the FC stack assembly only if the vehicle has been subjected to a strong impact.