WIRELESS DOOR LOCK CONTROL SYSTEM No Answer-Back

DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light answer-back function does not operate. In such cases, hazard warning light signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.

WIRING DIAGRAM

A01MJ2IE01

CAUTION / NOTICE / HINT

Note


  • The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication system is functioning properly.

    Click here

  • If the main body ECU (multiplex network body ECU) is replaced, refer to the entry and start system (for Entry Function).

    Click here

PROCEDURE


  1. CHECK CUSTOMIZE SETTING


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Wireless Door Lock.

    5. Select the setting by referring to the table below.


      Wireless Door Lock
      Tester Display Description Default Setting ECU
      Hazard Answer Back

      When the doors are locked by wireless operation, the hazard warning lights flash once.

      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

      		 ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
      Result
      Result Proceed to
      Customize setting in ON A
      Customize setting in OFF B

    B

    PERFORM CUSTOMIZE FUNCTION Click here

    A

  2. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS


    1. Check the wireless door lock control function using the electrical key transmitter sub-assembly.

      Result
      Result Proceed to
      Wireless door lock/unlock operates properly. A
      Wireless door lock/unlock does not operate properly. B

    B

    GO TO PROBLEM SYMPTOMS TABLE Click here

    A

  3. READ VALUE USING GTS (FR Door Lock Pos, FL Door Lock Pos, RR-Door Lock Pos SW, RL-Door Lock Pos SW)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      		 -
      FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      		 -
      RR-Door Lock Pos SW Rear door RH unlock detection switch signal OFF or ON

      OFF: Rear door RH locked

      ON: Rear door RH unlocked

      		 -
      RL-Door Lock Pos SW Rear door LH unlock detection switch signal OFF or ON

      OFF: Rear door LH locked

      ON: Rear door LH unlocked

      		 -

      Body Electrical > Main Body > Data List
      Tester Display
      FR Door Lock Pos
      FL Door Lock Pos
      RR-Door Lock Pos SW
      RL-Door Lock Pos SW
      OK
      The GTS display changes correctly in response to the lock/unlock operation.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) Click here

    OK

  4. CHECK HAZARD WARNING LIGHTS OPERATION


    1. Check that the hazard warning lights blink when the hazard warning signal switch is pressed.

      OK
      Hazard warning lights blink.
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    GO TO LIGHTING SYSTEM (Proceed to Hazard Warning Switch Circuit) Click here