NAVIGATION SYSTEM, Diagnostic DTC:B1324

DTC Code DTC Name
B1324 Lost Communication with Meter

DESCRIPTION

This DTC is stored when a communication error occurs between the radio and display receiver assembly and combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter After the radio and display receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the power switch is on (ACC), 1 or more times, the radio and display receiver assembly cannot receive the signal for 30 seconds or more.

  • Combination meter assembly

  • Radio and display receiver assembly

  • Harness or connector

WIRING DIAGRAM

A01MGL1E52
*a Combination Meter Assembly
*b Radio and Display Receiver Assembly
*c Local Bus Communication Line

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)


    1. Disconnect the G106 radio and display receiver assembly connector.

    2. Disconnect the G13 combination meter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G106-3 (CNH1) - G13-33 (MSCH) Always Below 1 Ω
      G106-4 (CNL1) - G13-34 (MSCL) Always Below 1 Ω
      G106-3 (CNH1) - Body ground Always 10 kΩ or higher
      G106-4 (CNL1) - Body ground Always 10 kΩ or higher
      G106-3 (CNH1) - G106-4 (CNL1) Always 10 kΩ or higher

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G106-3 (CNH1) - Body ground Always Below 1 V
      G106-4 (CNL1) - Body ground Always Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT COMBINATION METER ASSEMBLY


    1. Remove the combination meter assembly.

      Click here

    2. A01MHP6C02
      *a

      Component without harness connected

      (Combination Meter Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      33 (MSCH) - 34 (MSCL) Always 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

  3. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    1. Remove the radio and display receiver assembly.

      Click here

    2. A01MGZ1C05
      *a

      Component without harness connected

      (Radio and Display Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (CNH1) - 4 (CNL1) Always 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    OK

  4. REPLACE COMBINATION METER ASSEMBLY


    1. Replace the combination meter assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    OK

  5. CHECK METER / GAUGE SYSTEM


    1. Turn the power switch on (IG) and wait 30 seconds.

    2. Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.

      OK
      Audio system returns to normal.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here