POWER STEERING SYSTEM, Diagnostic DTC:C1552/22, C1554/23

DTC Code DTC Name
C1552/22 PIG Power Supply Voltage Malfunction
C1554/23 Power Supply Relay Failure

DESCRIPTION

When a problem occurs in the power steering system, the power source relay circuit is shut off to stop the power assist.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1552/22 PIG Power Supply Voltage Malfunction PIG power source circuit malfunction inside ECU

  • EPS fuse

  • PIG power source circuit

  • ECU wire sub-assembly

  • Power steering ECU assembly

 On Power switch on (IG) again -
C1554/23 Power Supply Relay Failure Power source relay circuit malfunction

  • EPS fuse

  • PIG power source circuit

  • ECU wire sub-assembly

  • Power steering ECU assembly

 On Power switch on (IG) again -

WIRING DIAGRAM

A01MFQ8E02
*a from Auxiliary Battery
*b Power Steering ECU Assembly

CAUTION / NOTICE / HINT

Note

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click here

Tech Tips


  • When DTC C1551/25 is detected together with DTCs C1552/22 and C1554/23, inspect and repair the trouble areas indicated by DTC C1551/25 first.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE


    1. Check the connection condition of the power steering ECU assembly connectors.

      OK
      The power steering ECU assembly connectors are securely connected.

    2. Check that the ground wire is securely installed with the bolt.

      Click here

      OK
      The ground wire is securely installed with the bolt.
      Result
      Proceed to
      OK
      NG

    NG

    CONNECT CONNECTOR OR INSTALL GROUND WIRE

    OK

  2. READ VALUE USING GTS (PIG POWER SUPPLY)


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / EMPS / Data List.

    6. Select the item "PIG Power Supply" in the Data List and read the value displayed on the GTS.


      Chassis > EMPS > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      PIG Power Supply Power source voltage to active motor

      Min.: 0.0000 V

      Max.: 20.1531 V

      		 Always: 9 to 16 V -

      Chassis > EMPS > Data List
      Tester Display
      PIG Power Supply
      OK
      The normal condition value is displayed on the GTS.
      Result
      Proceed to
      OK
      NG

    OK

    CHECK INTERMITTENT PROBLEMS Click here

    NG

  3. CHECK HARNESS AND CONNECTOR


    1. A01MJXJC07
      *a

      Front view of wire harness connector

      (to Power Steering ECU Assembly)

      Disconnect the A24 power steering ECU assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A24-1 (PIG) - Body ground Always 9 to 16 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A24-2 (PGND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER STEERING ECU ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS AND CONNECTOR Click here