HYBRID VEHICLE TRANSAXLE COMPONENTS
ILLUSTRATION
| *1 | FRONT FLOOR COVER LH | *2 | FRONT FLOOR COVER RH |
| *3 | NO. 1 MOTOR UNDER COVER | *4 | NO. 2 MOTOR UNDER COVER |
| *5 | REAR MOTOR UNDER COVER LH | *6 | REAR MOTOR UNDER COVER RH |
ILLUSTRATION
| *1 | FILLER PLUG | *2 | DRAIN PLUG |
| *3 | GASKET | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | FC COOLING WATER TEMPERATURE CONTROL VALVE | *2 | FC COOLING WATER VALVE INLET PIPE |
| *3 | FC COOLING BY-PASS PIPE | *4 | FC RADIATOR INLET PIPE |
| *5 | NO. 1 INVERTER COOLING OUTLET HOSE | *6 | INVERTER COOLING OUTLET PIPE |
| *7 | NO. 2 WATER HOSE SUB-ASSEMBLY | *8 | HEATER WATER INLET B HOSE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FCV TRACTION MOTOR BOND CABLE ASSEMBLY | *2 | MOTOR WIRE |
| *3 | MOTOR CABLE | *4 | UPPER NO. 1 RELAY BLOCK COVER |
| *5 | NO. 1 RELAY BLOCK COVER | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | COLUMN HOLE COVER SILENCER SHEET | *2 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH |
| *3 | REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH | *4 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
| *5 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY | *6 | FRONT CROSSMEMBER SUB-ASSEMBLY |
| *7 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | *8 | FRONT SUSPENSION MEMBER REAR BRACE LH |
| *9 | FRONT SUSPENSION MEMBER REAR BRACE RH | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | FCV TRANSAXLE WITH MOTOR ASSEMBLY | *2 | FC COOLING WATER PUMP ASSEMBLY |
| *3 | FC STACK COOLING WATER OUTLET BRACKET | *4 | HYDROGEN PUMP CABLE BRACKET |
| *5 | NO. 1 MOTOR COOLING HOSE | *6 | NO. 3 MOTOR COOLING HOSE |
| *7 | MOTOR MOUNTING INSULATOR LH | *8 | FC AIR COMPRESSOR CABLE BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FCV TRANSAXLE WITH MOTOR ASSEMBLY | *2 | FRONT MOTOR MOUNTING INSULATOR |
| *3 | REAR MOTOR MOUNTING INSULATOR | *4 | FRONT MOTOR MOUNTING BRACKET |
| *5 | MOTOR MOUNTING BRACKET LH | *6 | REAR MOTOR MOUNTING BRACKET |
| *7 | WIRE HARNESS CLAMP BRACKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FCV TRANSAXLE WITH MOTOR ASSEMBLY | *2 | FCV TRANSAXLE MASS DAMPER |
| *3 | OIL COOLER UNION SUB-ASSEMBLY | *4 | OIL COOLER INLET TUBE SUB-ASSEMBLY |
| *5 | TRANSAXLE BREATHER PLUG | *6 | STRAIGHT SCREW PLUG |
| *7 | TRANSAXLE HOUSING UNION | *8 | AUTOMATIC TRANSMISSION CASE COVER |
| *9 | NO. 2 AUTOMATIC TRANSMISSION CASE COVER | *10 | MOTOR CABLE BRACKET |
| *11 | NO. 2 OIL COOLER TUBE CLAMP | *12 | GASKET |
| *13 | O-RING | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with a union nut wrench | ● | Non-reusable part |
 |
ATF WS | - | - |