HYDROGEN TANK ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | NO. 1 FLOOR UNDER COVER | *2 | NO. 2 FLOOR UNDER COVER |
| *3 | FRONT FLOOR CENTER COVER LH | *4 | FRONT FLOOR CENTER COVER RH |
| *5 | FRONT FLOOR COVER LH | *6 | FRONT FLOOR COVER RH |
| *7 | NO. 2 MOTOR UNDER COVER | - | - |
ILLUSTRATION
| *1 | FC EXHAUST TAIL PIPE ASSEMBLY | *2 | NO. 2 FC EXHAUST PIPE |
| *3 | NO. 3 FC EXHAUST PIPE | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | LUGGAGE TRIM SERVICE HOLE COVER | *2 | NEGATIVE AUXILIARY BATTERY TERMINAL |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | REAR BUMPER SIDE SEAL LH | *2 | REAR WHEEL HOUSE FRONT PLATE LH |
| *3 | REAR WHEEL HOUSE LINER LH | - | - |
ILLUSTRATION
| *1 | NO. 2 PARKING BRAKE CABLE ASSEMBLY | *2 | NO. 3 PARKING BRAKE CABLE ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | NO. 1 HYDROGEN SUPPLY TUBE SUB-ASSEMBLY | *2 | NO. 2 HYDROGEN SUPPLY TUBE SUB-ASSEMBLY |
| *3 | HYDROGEN TANK TUBE ASSEMBLY | *4 | WIRING HARNESS CLAMP BRACKET |
| *5 | O-RING | *6 | HYDROGEN TANK TUBE CLAMP BRACKET |
| *7 | HYDROGEN INLET RECEPTACLE ASSEMBLY | *8 | HYDROGEN TANK UNIT |
| *9 | NO. 1 HYDROGEN SUPPLY REGULATOR PLUG | *10 | HYDROGEN SUPPLY REGULATOR UNION |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with 17 mm union nut wrench | ● | Non-reusable part |
 |
TOYOTA Genuine FC Grease | - | - |
ILLUSTRATION
| *1 | HYDROGEN TANK TUBE ASSEMBLY | *2 | NO. 2 HYDROGEN TANK TUBE ASSEMBLY |
| *3 | NO. 3 HYDROGEN TANK TUBE ASSEMBLY | *4 | NO. 4 HYDROGEN TANK TUBE |
| *5 | NO. 5 HYDROGEN TANK TUBE | *6 | HYDROGEN TANK TUBE CLAMP BRACKET |
| *7 | NO. 1 FUEL TUBE CLAMP | *8 | FUEL TUBE GROMMET |
| *9 | WIRE HARNESS CLAMP | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | * | For use with 17 mm union nut wrench |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | NO. 1 HYDROGEN TANK ASSEMBLY | *2 | NO. 2 HYDROGEN TANK ASSEMBLY |
| *3 | FRONT HYDROGEN TANK BAND SUB-ASSEMBLY | *4 | REAR HYDROGEN TANK BAND SUB-ASSEMBLY |
| *5 | FRONT HYDROGEN TANK FRAME SPRING BOLT CUSHION | *6 | REAR HYDROGEN TANK FRAME SPRING BOLT CUSHION |
| *7 | FRONT HYDROGEN TANK FRAME SUB-ASSEMBLY RH | *8 | FRONT HYDROGEN TANK FRAME SUB-ASSEMBLY LH |
| *9 | REAR HYDROGEN TANK FRAME SUB-ASSEMBLY | *10 | FRONT HYDROGEN TANK CENTER FRAME |
| *11 | COMPRESSION SPRING | *12 | FRONT HYDROGEN TANK SPRING BOLT CUP |
| *13 | REAR HYDROGEN TANK SPRING BOLT CUP | *14 | FRONT HYDROGEN TANK FRAME SEAT |
| *15 | REAR HYDROGEN TANK FRAME SEAT | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | LABEL | *2 | LABEL COVER FILM |
| ● | Non-reusable part | - | - |