Click here

REAR TURN SIGNAL LIGHT BULB REPLACEMENT

Click here
Click here

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here

PROCEDURE


  1. Click here

    DISCONNECT REAR COMBINATION LIGHT ASSEMBLY LH (w/ Deck)


    1. Open the tail gate.

    2. A01LC73C01
      B00692L Protective Tape

      Apply protective tape around the rear combination light assembly LH.

    3. A01L962

      Remove the 2 bolts.

    4. A01L91PC01
      B0069FO Pull in this Direction

      Pull the rear combination light assembly LH as shown to detach the 2 clips and disconnect it.

  2. Click here

    REMOVE REAR COMBINATION LIGHT LENS LH (for Deck-less)


    1. A01LAZ7

      Disconnect the connector.

    2. A01LEQ7

      Remove the 4 screws and rear combination light lens LH.

  3. Click here

    REMOVE REAR COMBINATION LIGHT LENS RH (for Deck-less)


    1. A01LFJX

      Remove the 4 screws and rear combination light lens RH.

  4. Click here

    REMOVE REAR TURN SIGNAL LIGHT BULB


    1. A01LE5VC01
      *a Matchmark
      *b Unlock Position Mark
      B0069FO Counterclockwise

      w/ Deck:


      1. Turn the bulb socket counterclockwise until the matchmark is aligned with the unlock position mark to disconnect the bulb socket.

      2. A01L88VC01
        B0069FO Push in this Direction
        B0068NX Counterclockwise
        A01LA3O Remove in this Direction

        Push the rear turn signal light bulb in the direction indicated by the black arrow shown in the illustration, turn the bulb counterclockwise, and then remove the bulb from the bulb socket.

    2. A01LAOVC01
      B0069FO Push in this Direction
      B0068NX Counterclockwise
      A01LA3O Remove in this Direction

      for Deck-less:

      Push the rear turn signal light bulb in the direction indicated by the black arrow shown in the illustration, turn the bulb counterclockwise, and then remove the bulb from the rear combination light body.

  5. Click here

    INSTALL REAR TURN SIGNAL LIGHT BULB


    1. A01LETUC02
      *a Protrusion
      B0068HS Cutout

      w/ Deck:


      1. Align the 2 protrusions on the back up light bulb with the 2 cutouts of the bulb socket and insert the bulb into the bulb socket.

      2. A01LE1RC01
        B0069FO Push in this Direction
        B0068NX Clockwise

        While pushing the rear turn signal light bulb, turn the bulb clockwise to install the bulb.

      3. A01LB2BC01
        *a Matchmark
        *b Unlock Position Mark
        *c Lock Position Mark
        B0069FO Clockwise

        Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.

    2. for Deck-less:


      1. A01LFOVC02
        *a Protrusion
        B0068HS Cutout

        Align the 2 protrusions on the rear turn signal light bulb with the 2 cutouts of the rear combination light body and insert the bulb to the rear combination light body.

      2. A01LCVQC01
        B0069FO Push in this Direction
        B0068NX Clockwise

        While pushing the rear turn signal light bulb, turn the bulb clockwise to install the bulb.

  6. Click here

    CONNECT REAR COMBINATION LIGHT ASSEMBLY LH (w/ Deck)


    1. A01L995C01
      B0069FO Install in this Direction
      B00692L Protective Tape

      Attach the 2 clips to install the rear combination light assembly LH.

    2. A01LEGWC01
      B0068AS Place Hands Here
      B0069FO Push in this Direction

      Install the 2 bolts.

      4.0 N*m 41 kgf*cm 35 in.*lbf
      Tip:

      Place your hands at the location shown in the illustration and while pushing the rear combination light assembly LH indicated by the arrow, tighten the 2 bolts.

    3. Close the tail gate.

  7. Click here

    INSTALL REAR COMBINATION LIGHT LENS LH (for Deck-less)


    1. Install the rear combination light lens LH with the 4 screws.

    2. Connect the connector.

  8. Click here

    INSTALL REAR COMBINATION LIGHT LENS RH (for Deck-less)


    1. Install the rear combination light lens RH with the 4 screws.