OUTER MIRROR SWITCH INSPECTION

PROCEDURE


  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (for LHD, w/ Power Retract Mirror)


    1. A01LAR9C01
      *a

      Component without harness connected

      (Outer Mirror Switch Assembly)
      *b Mirror Retract Switch
      *c Mirror Select Switch and Mirror Surface Adjust Switch

      Check the mirror retract switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition

        1 (MR) - 5 (E2)

        4 (MF) - 2 (+B2)

        		 Extended position Below 1 Ω

        1 (MR) - 2 (+B2)

        4 (MF) - 5 (E2)

        		 Retracted position Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check the mirror select switch and mirror surface adjust switch.


      1. Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for Left Side)
        Tester Connection Condition Specified Condition

        7 (B) - 10 (VL)

        15 (E) - 13 (M+)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 13 (M+)

        15 (E) - 10 (VL)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 9 (HL)

        15 (E) - 13 (M+)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 13 (M+)

        15 (E) - 9 (HL)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for Right Side)
        Tester Connection Condition Specified Condition

        7 (B) - 12 (VR)

        15 (E) - 13 (M+)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 13 (M+)

        15 (E) - 12 (VR)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 11 (HR)

        15 (E) - 13 (M+)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 13 (M+)

        15 (E) - 11 (HR)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

  2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (for LHD, w/o Power Retract Mirror)


    1. A01L9B9C01
      *a

      Component without harness connected

      (Outer Mirror Switch Assembly)
      *b Mirror Select Switch and Mirror Surface Adjust Switch

      Check the mirror select switch and mirror surface adjust switch.


      1. Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for Left Side)
        Tester Connection Condition Specified Condition

        7 (B) - 10 (VL)

        15 (E) - 13 (M+)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 13 (M+)

        15 (E) - 10 (VL)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 9 (HL)

        15 (E) - 13 (M+)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 13 (M+)

        15 (E) - 9 (HL)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for Right Side)
        Tester Connection Condition Specified Condition

        7 (B) - 12 (VR)

        15 (E) - 13 (M+)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 13 (M+)

        15 (E) - 12 (VR)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 11 (HR)

        15 (E) - 13 (M+)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        7 (B) - 13 (M+)

        15 (E) - 11 (HR)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

  3. INSPECT OUTER MIRROR SWITCH ASSEMBLY (for RHD, w/ Power Retract Mirror)


    1. A01LBLVC01
      *a

      Component without harness connected

      (Outer Mirror Switch Assembly)
      *b Mirror Retract Switch
      *c Mirror Select Switch and Mirror Surface Adjust Switch

      Check the mirror retract switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition

        5 (MR) - 1 (E2)

        2 (MF) - 4 (+B2)

        		 Extended position Below 1 Ω

        5 (MR) - 4 (+B2)

        2 (MF) - 1 (E2)

        		 Retracted position Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check the mirror select switch and mirror surface adjust switch.


      1. Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for Left Side)
        Tester Connection Condition Specified Condition

        15 (B) - 12 (VL)

        7 (E) - 9 (M+)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 9 (M+)

        7 (E) - 12 (VL)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 13 (HL)

        7 (E) - 9 (M+)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 9 (M+)

        7 (E) - 13 (HL)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for Right Side)
        Tester Connection Condition Specified Condition

        15 (B) - 10 (VR)

        7 (E) - 9 (M+)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 9 (M+)

        7 (E) - 10 (VR)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 11 (HR)

        7 (E) - 9 (M+)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 9 (M+)

        7 (E) - 11 (HR)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

  4. INSPECT OUTER MIRROR SWITCH ASSEMBLY (for RHD, w/o Power Retract Mirror)


    1. A01LEEMC01
      *a

      Component without harness connected

      (Outer Mirror Switch Assembly)
      *b Mirror Select Switch and Mirror Surface Adjust Switch

      Check the mirror select switch and mirror surface adjust switch.


      1. Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for Left Side)
        Tester Connection Condition Specified Condition

        15 (B) - 12 (VL)

        7 (E) - 9 (M+)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 9 (M+)

        7 (E) - 12 (VL)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 13 (HL)

        7 (E) - 9 (M+)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 9 (M+)

        7 (E) - 13 (HL)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for Right Side)
        Tester Connection Condition Specified Condition

        15 (B) - 10 (VR)

        7 (E) - 9 (M+)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 9 (M+)

        7 (E) - 10 (VR)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 11 (HR)

        7 (E) - 9 (M+)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        15 (B) - 9 (M+)

        7 (E) - 11 (HR)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.