FUEL LID LOCK CONTROL CABLE ASSEMBLY(for Double Cab) REMOVAL

PROCEDURE


  1. REMOVE FRONT SEAT ASSEMBLY RH (for RHD)


    1. for Manual Seat:

      Click here

    2. for Power Seat:

      Click here

  2. REMOVE FRONT SEAT ASSEMBLY LH


    1. for Manual Seat:

      Tech Tips

      The procedure described below is for the RH side.

    2. for Power Seat:

      Tech Tips

      The procedure described below is for the RH side.

    3. for Bench Seat Type:

      Click here

  3. REMOVE REAR SEAT ASSEMBLY


    1. for Seat Cushion 60/40 Split Type:

      Click here

    2. for Seat Cushion Bench Type:

      Click here

  4. REMOVE CONSOLE BOX ASSEMBLY (for RHD, w/ Console Box Lid)

    Click here

  5. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (for RHD, w/ Rear Console Box)

    Click here

  6. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  7. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

    Click here

  8. REMOVE COWL SIDE TRIM BOARD RH (for RHD)

    Click here

  9. REMOVE COWL SIDE TRIM BOARD LH (for LHD)

    Click here

  10. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  11. REMOVE LOWER CENTER PILLAR GARNISH LH

    Click here

  12. REMOVE LOWER QUARTER TRIM PANEL LH

    Click here

  13. REMOVE FRONT FLOOR CARPET ASSEMBLY


    1. Partially remove the floor carpet.

      Tech Tips

      It is not necessary to fully remove the floor carpet. Partially remove it so that the fuel lid lock control cable sub-assembly can be removed in a later step.

  14. REMOVE REAR WHEEL HOUSE LINER LH


    1. Partially remove the liner.

      Tech Tips

      It is not necessary to fully remove the liner. Partially remove it so that the fuel lid lock control cable sub-assembly can be removed in a later step.

  15. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for LHD)


    1. B002945

      Detach the claw and remove the fuel lid lock open lever sub-assembly.

  16. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for RHD)


    1. B0028BF

      Detach the claw and remove the fuel lid lock open lever sub-assembly.

  17. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)


    1. Remove the grommet from the vehicle body.

    2. Detach each clamp as shown in the illustration.

      B0027PAC01
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Grommet
    3. B002691C01
      B0069FO Remove in this Direction

      Detach the claw and remove the fuel lid lock control cable sub-assembly from the fuel filler opening lid lock retainer as shown in the illustration.

  18. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)


    1. Remove the grommet from the vehicle body.

    2. Detach each clamp as shown in the illustration.

      B0028DLC07
      *A for 4WD and Pre-Runner without VSC - -
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Grommet
    3. B002691C01
      B0069FO Remove in this Direction

      Detach the claw and remove the fuel lid lock control cable sub-assembly from the fuel filler opening lid lock retainer as shown in the illustration.

  19. REMOVE FUEL FILLER OPENING LID LOCK RETAINER


    1. B0024VLC01
      *a 90°
      B0069FO Remove in this Direction (1)
      B0068NX Remove in this Direction (2)
      B0027KK Remove in this Direction (3)

      Remove the fuel filler opening lid lock retainer as shown in the illustration.