Click here

REAR SEAT ASSEMBLY(for Seat Cushion Bench Type) REASSEMBLY

Click here
Click here

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Click here

PROCEDURE


  1. Click here

    INSTALL REAR SEAT HINGE COVER RH

    Note:

    • Perform the following only when replacing the rear seat hinge cover RH.

    • Do not reuse the rear seat hinge cover RH after removing it.


    1. A01L94QC01
      B0069FO Install in this Direction (1)
      B0068NX Install in this Direction (2)

      Push in installation direction (1) shown in the illustration to attach the guide.

    2. Push in installation direction (2) shown in the illustration to attach the claw to install a new rear seat hinge cover RH.

  2. Click here

    INSTALL REAR SEAT HINGE COVER LH

    Note:

    • Perform the following only when replacing the rear seat hinge cover LH.

    • Do not reuse the rear seat hinge cover LH after removing it.

    Tip:

    Use the same procedure described for the RH side.

  3. Click here

    INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY


    1. A01LC3U

      Install the No. 1 fold seat stopper band assembly to the rear No. 2 seat lock assembly.

  4. Click here

    INSTALL REAR NO. 2 SEAT LOCK ASSEMBLY


    1. A01LAGN

      Install the rear No. 2 seat lock assembly together with the No. 1 fold seat stopper band assembly with the 2 bolts.

      13 N*m 133 kgf*cm 10 ft.*lbf
  5. Click here

    INSTALL REAR SEAT CUSHION SIDE BRACKET RH


    1. A01L8S4

      Install the rear seat cushion side bracket RH with the bolt.

      43 N*m 438 kgf*cm 32 ft.*lbf
  6. Click here

    INSTALL REAR SEAT CUSHION SIDE BRACKET LH

    Tip:

    Use the same procedure described for the RH side.

  7. Click here

    INSTALL NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY


    1. A01LAF6

      Install the No. 1 seat cushion frame sub-assembly together with the 2 rear seat cushion side brackets with the 2 bushes and 2 bolts.

      13 N*m 133 kgf*cm 10 ft.*lbf
  8. Click here

    INSTALL REAR SEAT CUSHION COVER RH


    1. A01LBM7C01
      B0069FO Install in this Direction (1)
      B0068NX Install in this Direction (2)

      Push in installation direction (1) shown in the illustration to attach the guide.

    2. Push in installation direction (2) shown in the illustration to attach the claw to install the rear seat cushion cover RH.

  9. Click here

    INSTALL REAR SEAT CUSHION COVER LH

    Tip:

    Use the same procedure described for the RH side.

  10. Click here

    INSTALL SEAT COVER WIRE


    1. A01L9VJN01

      Install the seat cover wire.

      Tip:

      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.

      • For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read the precautions before preparing the wire.

        Click here

      Dimensions
      A 270 mm (10.63 in.)
      B 180 mm (7.09 in.)
      C 120 mm (4.72 in.)
      A01LDXU
      Tip:

      The dimensions shown in the illustration are the lengths.

  11. Click here

    INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY

    Tip:

    • When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

      Click here

    • A01LDGGN01

      Align the seam allowance in a single direction as shown in the illustration.


    1. A01LBGQC01
      *1 Hog Ring Pliers - -
      *a Cutout - -

      Using hog ring pliers, install the No. 1 seat cushion cover sub-assembly to the No. 1 seat cushion pad with 24 new hog rings in the order indicated in the illustration.

      Note:

      • Be careful not to damage the No. 1 seat cushion cover sub-assembly RH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seat cushion cover sub-assembly RH.

      Tip:

      Install the hog rings at the cutouts if they are there.

  12. Click here

    INSTALL REAR SEAT CUSHION COVER WITH PAD


    1. A01L9AEC01
      B0069FO Install in this Direction

      Install the rear seat cushion cover with pad to the No. 1 seat cushion frame sub-assembly.

    2. A01LEHG

      Pass the No. 1 fold seat stopper band assembly through the hole of the No. 1 seat cushion cover sub-assembly.

    3. A01LDKP

      Close the 2 fasteners.

    4. A01L9BJ

      Store the 2 fasteners.

    5. A01LCVN

      Attach the hook.

  13. Click here

    INSTALL SEAT COVER WIRE


    1. A01L9Y0N01

      Install the seat cover wire.

      Tip:

      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.

      • For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read the precautions before preparing the wire.

        Click here

      Dimensions
      A 270 mm (10.63 in.) B 300 mm (11.81 in.)
      A01LDXU
      Tip:

      The dimensions shown in the illustration are the lengths.

  14. Click here

    INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY

    Tip:

    • When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

      Click here

    • A01LDLSN01

      Align the seam allowance in a single direction as shown in the illustration.


    1. A01LG71C01
      *1 Hog Ring Pliers - -
      *a Cutout - -

      Using hog ring pliers, install the No. 1 seatback cover sub-assembly to the No. 1 seatback pad with 12 new hog rings in the order indicated in the illustration.

      Note:

      • Be careful not to damage the No. 1 seatback cover sub-assembly.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly.

      Tip:

      Install the hog rings at the cutouts if they are there.

  15. Click here

    INSTALL REAR SEATBACK COVER WITH PAD


    1. A01LF0PC01
      B0069FO Install in this Direction (1)
      B0068NX Install in this Direction (2)

      Push in installation direction (1) shown in the illustration to install the rear seatback cover with pad.

    2. Push in the rear end of the rear seatback cover with pad in installation direction (2) shown in the illustration.

    3. A01LEYON01

      Attach the hooks in the order indicated in the illustration.

  16. Click here

    INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY


    1. A01L8C5C01
      B0069FO Install in this Direction

      w/o Center Headrest:

      Attach the claw to install the 4 rear No. 1 seat headrest support assemblies.

    2. A01L9Z8C01
      B0069FO Install in this Direction

      w/ Center Headrest:

      Attach the claw to install the 6 rear No. 1 seat headrest support assemblies.

  17. Click here

    INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (w/ Center Headrest)


    1. Install the rear seat center headrest assembly.

  18. Click here

    INSTALL REAR SEAT HEADREST ASSEMBLY


    1. Install the 2 rear seat headrest assemblies.

    2. Attach the No. 1 fold seat stopper band assembly to the stay of the rear seat headrest assembly and temporarily fix the rear seat cushion assembly in place.