Click here

FRONT SEAT ASSEMBLY(for Power Seat) REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures(adjustment, calibration, initialization, or registration) that must be per formed after parts are removed, installed, or replaced during the front seat assembly removal / installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 40 minutes) Stop and start system

Click here
Memorize steering angle neutral point Pre-crash safety system

Click here
CAUTION:

  • B0025TC

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

  • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    CAUTION:
    B0069A2

    Be sure to read Precaution thoroughly before servicing.

    AIRBAG SYSTEM (for Type A):

    Click here

    AIRBAG SYSTEM (for Type B):

    Click here

    AIRBAG SYSTEM (for Type C):

    Click here

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. Click here

    REMOVE FRONT SEAT REAR OUTER TRACK COVER LH (w/ Cover)


    1. Operate the power seat switch knob LH (for Slide) to slide the front seat assembly LH to the frontmost position.

    2. B00264XC01
      B0069FO Remove in this Direction (1)
      B0068NX Remove in this Direction (2)

      While lifting up the part in the removal direction (1) shown in the illustration, detach the claw.

    3. Pull out removal direction (2) shown in the illustration to detach the guide and remove the front seat rear outer track cover LH.

  3. Click here

    REMOVE FRONT SEAT REAR INNER TRACK COVER LH (w/ Cover)


    1. B00264MC01
      B0069FO Remove in this Direction (1)
      B0068NX Remove in this Direction (2)

      While lifting up the part in the removal direction (1) shown in the illustration, detach the claw.

    2. Pull out removal direction (2) shown in the illustration to detach the guide and remove the front seat rear inner track cover LH.

  4. Click here

    REMOVE FRONT SEAT ASSEMBLY LH


    1. B00267T

      Remove the 2 bolts on the rear side of the front seat assembly LH.

    2. Operate the power seat switch knob LH (for Slide) to slide the front seat assembly LH to the rearmost position.

    3. B0024TF

      Remove the 2 bolts.

    4. Operate the power seat switch knob LH (for Slide) to slide the front seat assembly LH to the center position.

    5. Operate the power seat switch knob LH (for Vertical) to set the seat cushion height of the front seat assembly LH to the uppermost position.

    6. Operate the power seat switch knob LH (for Reclining) to set the seatback of the front seat assembly LH to the perpendicular position.

    7. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      B00693Q

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    8. w/ Front Seat Side Airbag:

      Disconnect the front seat airbag assembly LH connector.


      1. B00280EC12
        *1 Slider - -
        *a Push *b Slide

        Push the slider to detach the primary lock. Continue pushing and slide the slider to detach the secondary lock and then disconnect the airbag connector.

    9. B0025XJ

      Disconnect the 2 connectors.

    10. Detach the wire harness clamp.

    11. B0024I1

      Remove the front seat assembly LH as shown in the illustration.

      Note:

      • Protect the front seat legs.


      • Do not damage the front seat assembly LH, body exterior or interior parts.