FRONT SEAT ASSEMBLY(for Power Seat) REMOVAL

CAUTION / NOTICE / HINT

CAUTION:


  • B0025TC

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

  • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    AIRBAG SYSTEM (for Type A):

    Click here

    AIRBAG SYSTEM (for Type B):

    Click here

    B0069A2

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

    Click here

  2. REMOVE FRONT SEAT REAR OUTER TRACK COVER LH (w/ Cover)


    1. Operate the power seat switch knob LH (for Slide) to slide the front seat assembly LH to the frontmost position.

    2. B00264XC01
      B0069FO Remove in this Direction (1)
      B0068NX Remove in this Direction (2)

      While lifting up the part in the removal direction (1) shown in the illustration, detach the claw.

    3. Pull out removal direction (2) shown in the illustration to detach the guide and remove the front seat rear outer track cover LH.

  3. REMOVE FRONT SEAT REAR INNER TRACK COVER LH (w/ Cover)


    1. B00264MC01
      B0069FO Remove in this Direction (1)
      B0068NX Remove in this Direction (2)

      While lifting up the part in the removal direction (1) shown in the illustration, detach the claw.

    2. Pull out removal direction (2) shown in the illustration to detach the guide and remove the front seat rear inner track cover LH.

  4. REMOVE FRONT SEAT ASSEMBLY LH


    1. B00267T

      Remove the 2 bolts on the rear side of the front seat assembly LH.

    2. Operate the power seat switch knob LH (for Slide) to slide the front seat assembly LH to the rearmost position.

    3. B0024TF

      Remove the 2 bolts.

    4. Operate the power seat switch knob LH (for Slide) to slide the front seat assembly LH to the center position.

    5. Operate the power seat switch knob LH (for Vertical) to set the seat cushion height of the front seat assembly LH to the uppermost position.

    6. Operate the power seat switch knob LH (for Reclining) to set the seatback of the front seat assembly LH to the perpendicular position.

    7. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B00693Q

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    8. w/ Side Airbag System:

      Disconnect the front seat airbag assembly LH connector.


      1. Push the slider to detach the primary lock. Continue pushing and slide the slider to detach the secondary lock and then disconnect the airbag connector.

        B00280EC12
        *1 Slider - -
        *a Push *b Slide
    9. B0025XJ

      Disconnect the 2 connectors.

    10. Detach the wire harness clamp.

    11. B0024I1

      Remove the front seat assembly LH as shown in the illustration.

      Note


      • Protect the front seat legs.


      • Do not damage the front seat assembly LH, body exterior or interior parts.