PRE-CRASH SAFETY SYSTEM FREEZE FRAME DATA


  1. DESCRIPTION


    1. When a pre-crash safety system DTC is stored, the millimeter wave radar sensor assembly stores the current vehicle (ECU or sensor) state as Freeze Frame Data.

  2. CHECK FREEZE FRAME DATA


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.


      Body Electrical > Pre-Crash 2 > Trouble Codes

    5. According to the GTS display, select a DTC that stored freeze frame data.

    6. Read the freeze frame data recorded when the DTC was stored.


      Body Electrical > Pre-Crash 2
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Turn Light RH Turn signal switch (right) status ON or OFF

      ON: Turn signal switch (right) on

      OFF: Turn signal switch (right) off

      		 -
      Turn Light LH Turn signal switch (left) status ON or OFF

      ON: Turn signal switch (left) on

      OFF: Turn signal switch (left) off

      		 -
      PCS OFF Switch Pre-crash safety system on/off status ON or OFF

      ON: Pre-crash safety system on

      OFF: Pre-crash safety system off

      		 -
      PCS Indicator

      • "Pre-Crash Safety Malfunction Visit Your Dealer" display request signal*1

      • "PRE-CRASH SAFETY MALFUNCTION VISIT YOUR DEALER" display request signal*2

      		 ON or OFF

      • ON: "Pre-Crash Safety Malfunction Visit Your Dealer" display requested*1

      • OFF: "Pre-Crash Safety Malfunction Visit Your Dealer" display not requested*1


      • ON: "PRE-CRASH SAFETY MALFUNCTION VISIT YOUR DEALER" display requested*2

      • OFF: "PRE-CRASH SAFETY MALFUNCTION VISIT YOUR DEALER" display not requested*2

      		 -
      PCS Disabled Indicator

      • "Pre-Crash Safety Unavailable" display request signal*1

      • "PRE-CRASH SAFETY UNAVAILABLE" display request signal*2

      		 ON or OFF

      • ON: "Pre-Crash Safety Unavailable" display requested*1

      • OFF: "Pre-Crash Safety Unavailable" display not requested*1


      • ON: "PRE-CRASH SAFETY UNAVAILABLE" display requested*2

      • OFF: "PRE-CRASH SAFETY UNAVAILABLE" display not requested*2

      		 -
      Pre-Crash Safety Warning Buz Pre-crash safety system warning buzzer Valid or Inval

      Valid: Pre-crash safety system warning buzzer operation possible

      Inval: Pre-crash safety system warning buzzer operation not possible

      		 -
      Pre-Crash Brake Pre-crash brake function Valid or Inval

      Valid: Pre-crash brake operation possible

      Inval: Pre-crash brake operation not possible

      		 -
      PBA Start Pre-crash brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2

      OFF: Pre-crash brake assist not operating

      Standby: Brake pedal not depressed during pre-crash brake assist operation

      Assist Lv1: Brake pedal depressed during pre-crash brake assist operation

      Assist Lv2: Brake pedal firmly depressed during pre-crash brake assist operation

      		 Signal status changes when the pre-crash brake assist is activated before a crash (Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
      Brake Assist Standby - - - This item is displayed on the GTS but is not used.
      Pre-Crash Brake Control Pre-crash brake operational status ON or OFF

      ON: Pre-crash brake operating

      OFF: Pre-crash brake not operating

      		 -
      AVS Start - - - This item is displayed on the GTS but is not used.
      VGRS Start - - - This item is displayed on the GTS but is not used.
      PBA Control Pre-crash brake assist operational status Valid or Invalid

      Valid: Pre-crash brake assist control operation possible

      Invalid: Pre-crash brake assist control operation not possible

      		 -
      Pre-Crash Safety Brake Ind Pre-crash safety system alarm warning message status ON or OFF

      ON: Displayed

      OFF: Not displayed

      		 "BRAKE!" is displayed
      PCS Crash Alarm Buzzer Skid control buzzer status ON or OFF

      ON: Skid control buzzer sounding

      OFF: Skid control buzzer not sounding

      		 -
      Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history ON or OFF

      ON: History of low voltage

      OFF: No history of low voltage

      		 If the engine starts 1 second or more after the ignition switch was turned ON, this item may change to ON
      Front Recognition Camera-Malfunction History Forward recognition camera system unavailable history ON or OFF

      ON: History of unavailable

      OFF: No history of unavailable

      		 -
      Control Mode ECU control mode status Normal or Check Mode

      Normal: Normal operation

      Check Mode: Operating in Control Mode

      		 -
      PCS Operation State Retention Setting PCS Operation State Retention Setting customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -
      PCS Alarm Activation Distance Retention Setting 1 PCS Alarm Activation Distance Retention Setting 1 customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -
      PCS Alarm Activation Distance Retention Setting 2 PCS Alarm Activation Distance Retention Setting 2 customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -
      PCS Alarm Activation Distance Retention Setting 3 PCS Alarm Activation Distance Retention Setting 3 customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -

      • *1: for TFT Display Type

      • *2: for Dot Display Type