FRONT SEAT SIDE AIRBAG ASSEMBLY(for Power Seat) DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

    • If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

      B0024VO

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the front seat airbag assembly LH, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.

  2. DISPOSE OF FRONT SEAT AIRBAG ASSEMBLY LH (When Installed in Vehicle)

    Note


    • When disposing of the front seat airbag assembly LH, use an unneeded vehicle to deploy the airbag.

    • Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B0024CLN26

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Refer to Precaution.

      for Type B:

      Click here

      for Type C:

      Click here

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      B00693Q

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    4. B0027V6C02
      *a Housing Lock
      *b CPA Upper Part
      B00692L CPA

      Disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the airbag connector cannot be disconnected yet.)

      2. Push down the housing lock again and disconnect the airbag connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.

    5. Install SST.


      1. B0028UWN01

        Connect the SST connector to the airbag connector.

        SST
        09082-00700

        CAUTION:


        • B002536

          Do not deploy if the front seat airbag assembly LH is loose.

        • If deployed while the front seat airbag assembly LH is loose, the front seat airbag assembly LH may fly off and cause serious injuries.

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.

      2. B0024NVC02
        *a 10 m or more

        Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

      3. While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

        CAUTION:


        • Do not deploy with all the doors and door windows open.

        • If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.

        B00262C

        Note

        Take care not to damage the SST wire harness.

      4. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    6. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • Do not deploy with people inside or around the vehicle.

        • If deployed with people inside or around the vehicle, serious injuries may occur.

        B00273W

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    7. Remove the front seat airbag assembly LH.

      Click here

      CAUTION:


      • B00276Q

        The front seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B0026YY

        Do not apply water etc. to a front seat airbag assembly LH with a deployed airbag.

      • If water is applied to the front seat airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B0026R9

        Always wear safety glasses and gloves when handling a deployed front seat airbag assembly LH.

      • If the front seat airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • After removal, quickly seal the front seat airbag assembly LH in a plastic bag.

    8. Dispose of the front seat airbag assembly LH.


      1. Place the front seat airbag assembly LH in a plastic bag, tie it tightly and dispose of it according to local regulations.

        CAUTION:


        • B0024WG

          The front seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • If not left alone for 30 minutes or more, burns may occur when touched.

        • B0026VL

          Do not apply water etc. to a front seat airbag assembly LH with a deployed airbag.

        • If water is applied to the front seat airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

        • B0027U3

          Always wear safety glasses and gloves when handling a deployed front seat airbag assembly LH.

        • If the front seat airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

        • B002685

          Never dispose of a front seat airbag assembly LH with an undeployed airbag.

        • If an undeployed front seat airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

        • Always wash your hands with water after completing the operation.

  3. DISPOSE OF FRONT SEAT AIRBAG ASSEMBLY LH (When not Installed in Vehicle)

    Note

    Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B0024CLN26

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Remove the front seat airbag assembly LH.

      Click here

      CAUTION:

      B00693Q

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    3. B0026IAC28
      *a Wire Diameter
      *b Stripped Wire

      Using braided wire, tie down the front seat airbag assembly LH to an unneeded tire.

      Wire
      Cross-sectional area of stripped wire
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire harness is too thin or an alternative object is used to tie down the front seat airbag assembly LH, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the cross-sectional area of stripped wire:

      Area = 3.14 x (Diameter)2/ 4


      1. Install the 2 nuts to the front seat airbag assembly LH.

        B00295WC02
        *A for Type A *B for Type B

      2. Wind the wires around the stud bolts of the front seat airbag assembly LH as shown in the illustration.

        B00268DC02
        *A for Type A *B for Type B

      3. Position the front seat airbag assembly LH inside the tire.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)

        Note

        The tires may be damaged by the airbag deployment, so use unneeded tires.

        B0025VCC02
        *A for Type A *B for Type B
        *a Width *b Inner Diameter
        *c Deployment Side - -

    4. Install SST.


      1. Connect the SST connector to the front seat airbag assembly LH connector.

        SST
        09082-00820
        B00282FC02
        *A for Type A *B for Type B

    5. Place the tires.


      1. Place at least 2 tires under the tire to which the front seat airbag assembly LH is tied.

        B0027CKC02
        *A for Type A *B for Type B
        *a Tires (2 or more) - -

      2. Place at least 2 tires onto the tire to which the front seat airbag assembly LH is tied. The top tire should have a wheel installed.

        Note


        • Do not place the SST connector under the tire because it could be damaged.

        • The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.

      3. B002946

        Tie the tires together with the 2 wires.

    6. Install SST.


      1. Connect the SST connector.

        SST
        09082-00700

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

        B00263GC02
        *A for Type A *B for Type B
        *a 10 m or more - -

      2. Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.

    7. Deploy the airbag.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the front seat airbag assembly LH is tied.

      3. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • Do not deploy with people around the tire.

        • If deployed with people around the tire, serious injuries may occur.

        B0025TP

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    8. Dispose of the front seat airbag assembly LH.

      CAUTION:


      • B0024WG

        The front seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B0026VL

        Do not apply water etc. to a front seat airbag assembly LH with a deployed airbag.

      • If water is applied to the front seat airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B0027U3

        Always wear safety glasses and gloves when handling a deployed front seat airbag assembly LH.

      • If the front seat airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • B002685

        Never dispose of a front seat airbag assembly LH with an undeployed airbag.

      • If an undeployed front seat airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

      • Always wash your hands with water after completing the operation.


      1. Remove the front seat airbag assembly LH from the tire.

      2. Place the front seat airbag assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.