CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the curtain shield airbag assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Pre-collision system

Click here

Tech Tips


  • Use the same procedure for RHD and LHD sides.

  • The procedure listed below is for LHD sides.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    for Type B:

    B0069A2

    Click here

    for Type C:

    Click here

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B00693Q

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE ROOF HEADLINING ASSEMBLY

    for Single Cab:

    Click here

    for Double Cab:

    Click here

    for Smart Cab:

    Click here

  4. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

    CAUTION:

    B0025KZC01
    B00692L Deployment Side

    • When storing the curtain shield airbag assembly LH, keep the airbag deployment side facing upward.

    • If the airbag deploys for any reason, it may cause a serious accident.


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B00693Q
    3. B0024LYC01
      *a Connector Lock
      B00692L Protective Tape
      B0069FO Release in this Direction

      Using a screwdriver, pull up the connector lock and disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

      Tech Tips

      Tape the screwdriver tip before use.

    4. Remove the clip.

      Note

      The clip must not be reused.

      Tech Tips

      Use the same procedure for the other clips.


      1. B0025T7C01
        *1 Pin

        Using needle-nose pliers, release the lock by pinching the 2 locks of the pin, and then pull out the pin from the clip.

      2. B002702

        Using 2 screwdrivers, detach the clip by inserting the screwdrivers into the groove of the clip as shown in the illustration, and then remove the clip from the vehicle body.

    5. for Single Cab:


      1. Remove the 2 bolts.

        Note

        The bolts must not be reused.

      2. Detach the claw and remove the curtain shield airbag assembly LH.

        B002860
    6. for Double Cab:


      1. Remove the 2 bolts.

        Note

        The bolts must not be reused.

      2. Detach the claw and remove the curtain shield airbag assembly LH.

        B0028KL
    7. for Smart Cab:


      1. Remove the 2 bolts.

        Note

        The bolts must not be reused.

      2. Detach the claw and remove the curtain shield airbag assembly LH.

        B0028AM