AIRBAG SYSTEM(for Type B), Diagnostic DTC:B1820/55, B1821/55, B1822/55, B1823/55

DTC Code DTC Name
B1820/55 Short in Side Squib RH Circuit
B1821/55 Open in Side Squib RH Circuit
B1822/55 Short to GND in Side Squib RH Circuit
B1823/55 Short to B+ in Side Squib RH Circuit

DESCRIPTION

The front side squib RH circuit consists of the airbag sensor assembly and front seat airbag assembly RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1820/55 Short in Side Squib RH Circuit

One of the following conditions is met:


  • The airbag sensor assembly detects a line short circuit signal 5 times in the front side squib RH circuit during the primary check.

  • A front seat airbag assembly RH malfunction.

  • An airbag sensor assembly malfunction.

  • Floor wire

  • Front seat airbag assembly RH

  • Airbag sensor assembly
B1821/55 Open in Side Squib RH Circuit

One of the following conditions is met:


  • The airbag sensor assembly detects an open circuit signal in the front side squib RH circuit for 2 seconds.

  • A front seat airbag assembly RH malfunction.

  • An airbag sensor assembly malfunction.

  • Floor wire

  • Front seat airbag assembly RH

  • Airbag sensor assembly
B1822/55 Short to GND in Side Squib RH Circuit

One of the following conditions is met:


  • The airbag sensor assembly detects a short circuit to ground signal in the front side squib RH circuit for 0.5 seconds.

  • A front seat airbag assembly RH malfunction.

  • An airbag sensor assembly malfunction.

  • Floor wire

  • Front seat airbag assembly RH

  • Airbag sensor assembly
B1823/55 Short to B+ in Side Squib RH Circuit

One of the following conditions is met:


  • The airbag sensor assembly detects a short circuit to B+ signal in the front side squib RH circuit for 0.5 seconds.

  • A front seat airbag assembly RH malfunction.

  • An airbag sensor assembly malfunction.

  • Floor wire

  • Front seat airbag assembly RH

  • Airbag sensor assembly

WIRING DIAGRAM

B0027LIE10
*a Front Seat Airbag Assembly RH
*b Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

  • After replacing the airbag sensor assembly, refer to initialization*.

    Click here

    *: w/ VSC

Tech Tips

To perform the simulation method, enter check mode (signal check) with the GTS (Click here ), and then wiggle each connector of the airbag system or drive the vehicle on various types of road Click here.

PROCEDURE


  1. CHECK FRONT SEAT AIRBAG ASSEMBLY RH


    1. B0028FTC05
      *1 Front Seat Airbag Assembly RH
      *2 Airbag Sensor Assembly
      *3 Connector C
      *4 SST
      *a

      Front view of wire harness connector

      (to Front Seat Airbag Assembly RH)

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect the connector from the front seat airbag assembly RH.

    4. Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the front seat airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    5. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Clear the DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    8. Turn the ignition switch off.

    9. Turn the ignition switch to ON, and wait for at least 60 seconds.

    10. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.
      DTC B1820/55, B1821/55, B1822/55 or B1823/55 is output.

      Tech Tips

      Codes other than DTC B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.

    11. Turn the ignition switch off.

    12. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    13. Disconnect SST from connector C.


    DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.

    REPLACE FRONT SEAT AIRBAG ASSEMBLY RH for Power Seat: Click here
    REPLACE FRONT SEAT AIRBAG ASSEMBLY RH for Manual Seat: Click here

    DTC B1820/55, B1821/55, B1822/55 or B1823/55 is output.

  2. CHECK CONNECTORS


    1. Disconnect the connectors from the airbag sensor assembly.

    2. B00294FC24
      *1 Front Seat Airbag Assembly RH
      *2 Floor Wire
      *3 Airbag Sensor Assembly

      Check that the connectors (on the airbag sensor assembly side and front seat airbag assembly RH side) are not damaged.

      OK
      The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  3. CHECK FLOOR WIRE


    1. B0028SRC08
      *1 Front Seat Airbag Assembly RH
      *2 Floor Wire
      *3 Airbag Sensor Assembly
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Front Seat Airbag Assembly RH)

      Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N10-2 (SFR+) - Body ground Ignition switch ON Below 1 V
      N10-1 (SFR-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N10-2 (SFR+) - N10-1 (SFR-) Always Below 1 Ω

    7. Release the activation prevention mechanism built into connector B.

      Click here

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N10-2 (SFR+) - N10-1 (SFR-) Always 1 MΩ or higher

    9. Restore the released activation prevention mechanism of connector B to its original condition.

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N10-2 (SFR+) - Body ground Always 1 MΩ or higher
      N10-1 (SFR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK DTC


    1. B0028LOC29
      *1 Front Seat Airbag Assembly RH
      *2 Airbag Sensor Assembly

      Connect the connectors to the front seat airbag assembly RH and airbag sensor assembly.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output
      DTC B1820/55, B1821/55, B1822/55 or B1823/55 is output

      Tech Tips

      Codes other than DTC B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.


    DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output

    USE SIMULATION METHOD TO CHECK Click here

    DTC B1820/55, B1821/55, B1822/55 or B1823/55 is output

    REPLACE AIRBAG SENSOR ASSEMBLY Click here