AIRBAG SYSTEM(for Type C), Diagnostic DTC:B1692/81, B1693/81, B1697/82, B1698/82

DTC Code DTC Name
B1692/81 Lost Communication with Door Side Airbag Sensor RH
B1693/81 Door Side Airbag Sensor RH Initialization Incomplete
B1697/82 Lost Communication with Door Side Airbag Sensor LH
B1698/82 Door Side Airbag Sensor LH Initialization Incomplete

DESCRIPTION

The circuit for the side collision sensor LH or RH is composed of the airbag sensor assembly, side airbag sensor assembly LH or RH* and door side airbag sensor LH or RH.

The side airbag sensor assembly LH or RH* and door side airbag sensor LH or RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1692/81, B1693/81, B1697/82 or B1698/82 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH.

*: except Single Cab

DTC No. Detection Item DTC Detection Condition Trouble Area
B1692/81 Lost Communication with Door Side Airbag Sensor RH

One of the following conditions is met:


  • The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

  • A door side airbag sensor RH malfunction.

  • A side airbag sensor assembly RH malfunction.*

  • An airbag sensor assembly malfunction.

  • Floor wire

  • Front door wire RH

  • Door side airbag sensor RH

  • Side airbag sensor assembly RH*

  • Airbag sensor assembly
B1693/81 Door Side Airbag Sensor RH Initialization Incomplete

One of the following conditions is met:


  • The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

  • A door side airbag sensor RH malfunction.

  • A side airbag sensor assembly RH malfunction.*

  • An airbag sensor assembly malfunction.

  • Floor wire

  • Front door wire RH

  • Door side airbag sensor RH

  • Side airbag sensor assembly RH*

  • Airbag sensor assembly
B1697/82 Lost Communication with Door Side Airbag Sensor LH

One of the following conditions is met:


  • The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

  • A door side airbag sensor LH malfunction.

  • A side airbag sensor assembly LH malfunction.*

  • An airbag sensor assembly malfunction.

  • Floor wire

  • Front door wire LH

  • Door side airbag sensor LH

  • Side airbag sensor assembly LH*

  • Airbag sensor assembly
B1698/82 Door Side Airbag Sensor LH Initialization Incomplete

One of the following conditions is met:


  • The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

  • A door side airbag sensor LH malfunction.

  • A side airbag sensor assembly LH malfunction.*

  • An airbag sensor assembly malfunction.

  • Floor wire

  • Front door wire LH

  • Door side airbag sensor LH

  • Side airbag sensor assembly LH*

  • Airbag sensor assembly

*: except Single Cab

WIRING DIAGRAM

Figure 1. for Single Cab RH Side:

B0024IPE95
*a Door Side Airbag Sensor RH
*b Airbag Sensor Assembly

Figure 2. for Single Cab LH Side:

B0024IPE96
*a Door Side Airbag Sensor LH
*b Airbag Sensor Assembly

Figure 3. except Single Cab RH Side:

B0025C7E42
*a Airbag Sensor Assembly
*b Side Airbag Sensor Assembly RH
*c Door Side Airbag Sensor RH

Figure 4. except Single Cab LH Side:

B0025C7E43
*a Airbag Sensor Assembly
*b Side Airbag Sensor Assembly LH
*c Door Side Airbag Sensor LH

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

  • After replacing the airbag sensor assembly, refer to initialization.

    Click here

PROCEDURE


  1. CHECK VEHICLE TYPE


    1. Check vehicle condition.

      Result
      Result Proceed to
      for Single Cab A
      except Single Cab B

    B

    CHECK DTC Click here

    A

  2. CHECK DTC


    1. Turn the ignition switch to ON.

    2. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    3. Turn the ignition switch off.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1697/82 or B1698/82 is output
      DTC B1692/81 or B1693/81 is output
      DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

      Tech Tips

      Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.


    DTC B1692/81 or B1693/81 is output

    CHECK CONNECTION OF CONNECTORS Click here

    DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

    DTC B1697/82 or B1698/82 is output

  3. CHECK CONNECTION OF CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the airbag sensor assembly and door side airbag sensor LH.

      Result
      Proceed to
      The connectors are properly connected
      The connectors are not properly connected

    The connectors are not properly connected

    CONNECT CONNECTORS PROPERLY

    The connectors are properly connected

  4. CHECK CONNECTORS


    1. Disconnect the connectors from the airbag sensor assembly and door side airbag sensor LH.

    2. B0025CLC01
      *1 Door Side Airbag Sensor LH
      *2 Airbag Sensor Assembly
      *3 Front Door Wire LH
      *4 Floor Wire

      Check that the connectors (on the airbag sensor assembly side and door side airbag sensor LH side) are not damaged.

      Result
      Proceed to
      The connectors are not deformed or damaged
      The connectors are deformed or damaged

    The connectors are deformed or damaged

    REPLACE FLOOR WIRE OR FRONT DOOR WIRE LH

    The connectors are not deformed or damaged

  5. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT


    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      B0026LCC01
      *1 Door Side Airbag Sensor LH *2 Airbag Sensor Assembly
      *3 Front Door Wire LH *4 Floor Wire
      *5 Connector E *6 Connector B
      *7 Service Wire - -
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      		 *b

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K10-2 (BCL+) - Body ground Ignition switch ON Below 1 V
      K10-1 (BCL-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K10-2 (BCL+) - K10-1 (BCL-) Always Below 1 Ω

    8. Disconnect the service wire from connector B.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K10-2 (BCL+) - K10-1 (BCL-) Always 1 MΩ or higher
      K10-2 (BCL+) - Body ground Always 1 MΩ or higher
      K10-1 (BCL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE Click here

    OK

  6. CHECK DOOR SIDE AIRBAG SENSOR LH


    1. Connect the connectors to the airbag sensor assembly.

    2. B0026RLC01
      *1 Door Side Airbag Sensor RH
      *2 Airbag Sensor Assembly

      Interchange the door side airbag sensor LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1692/81 or B1693/81 is output
      DTC B1697/82 or B1698/82 is output
      DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

      Tech Tips

      Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.


    DTC B1692/81 or B1693/81 is output

    REPLACE DOOR SIDE AIRBAG SENSOR LH Click here

    DTC B1697/82 or B1698/82 is output

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

  7. CHECK FLOOR WIRE


    1. Disconnect the floor wire connector from the front door wire LH.

      B0026S7C01
      *1 Door Side Airbag Sensor LH *2 Airbag Sensor Assembly
      *3 Front Door Wire LH *4 Floor Wire
      *5 Connector C *6 Connector B
      *7 Service Wire - -
      *a

      Front view of wire harness connector

      (to Front Door Wire LH)

      		 *b

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      KN2-1 (BCL-) - Body ground Ignition switch ON Below 1 V
      KN2-2 (BCL+) - Body ground Ignition switch ON Below 1 V

    5. Turn the ignition switch off.

    6. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    7. Using a service wire, connect terminals 23 (BBL-) and 24 (BBL+) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      KN2-1 (BCL-) - KN2-2 (BCL+) Always Below 1 Ω

    9. Disconnect the service wire from connector B.

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      KN2-1 (BCL-) - KN2-2 (BCL+) Always 1 MΩ or higher
      KN2-1 (BCL-) - Body ground Always 1 MΩ or higher
      KN2-2 (BCL+) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE FLOOR WIRE

  8. CHECK CONNECTION OF CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the airbag sensor assembly and door side airbag sensor RH.

      Result
      Proceed to
      The connectors are properly connected
      The connectors are not properly connected

    The connectors are not properly connected

    CONNECT CONNECTORS PROPERLY

    The connectors are properly connected

  9. CHECK CONNECTORS


    1. Disconnect the connectors from the airbag sensor assembly and door side airbag sensor RH.

    2. B0024U1C01
      *1 Door Side Airbag Sensor RH
      *2 Airbag Sensor Assembly
      *3 Front Door Wire RH
      *4 Floor Wire

      Check that the connectors (on the airbag sensor assembly side and door side airbag sensor RH side) are not damaged.

      Result
      Proceed to
      The connectors are not deformed or damaged
      The connectors are deformed or damaged

    The connectors are deformed or damaged

    REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH

    The connectors are not deformed or damaged

  10. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT


    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      B002457C01
      *1 Door Side Airbag Sensor RH *2 Airbag Sensor Assembly
      *3 Front Door Wire RH *4 Floor Wire
      *5 Connector E *6 Connector B
      *7 Service Wire - -
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      		 *b

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      J10-2 (BCR+) - Body ground Ignition switch ON Below 1 V
      J10-1 (BCR-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J10-2 (BCR+) - J10-1 (BCR-) Always Below 1 Ω

    8. Disconnect the service wire from connector B.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J10-2 (BCR+) - J10-1 (BCR-) Always 1 MΩ or higher
      J10-2 (BCR+) - Body ground Always 1 MΩ or higher
      J10-1 (BCR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE Click here

    OK

  11. CHECK DOOR SIDE AIRBAG SENSOR RH


    1. Connect the connectors to the airbag sensor assembly.

    2. B0027BHC01
      *1 Door Side Airbag Sensor LH
      *2 Airbag Sensor Assembly

      Interchange the door side airbag sensor LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1692/81 or B1693/81 is output
      DTC B1697/82 or B1698/82 is output
      DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

      Tech Tips

      Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.


    DTC B1692/81 or B1693/81 is output

    REPLACE DOOR SIDE AIRBAG SENSOR RH Click here

    DTC B1697/82 or B1698/82 is output

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

  12. CHECK FLOOR WIRE


    1. Disconnect the floor wire connector from the front door wire RH.

      B00294BC01
      *1 Door Side Airbag Sensor RH *2 Airbag Sensor Assembly
      *3 Front Door Wire RH *4 Floor Wire
      *5 Connector C *6 Connector B
      *7 Service Wire - -
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      		 *b

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      JN2-1 (BCR-) - Body ground Ignition switch ON Below 1 V
      JN2-2 (BCR+) - Body ground Ignition switch ON Below 1 V

    5. Turn the ignition switch off.

    6. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    7. Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN2-1 (BCR-) - JN2-2 (BCR+) Always Below 1 Ω

    9. Disconnect the service wire from connector B.

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JN2-1 (BCR-) - JN2-2 (BCR+) Always 1 MΩ or higher
      JN2-1 (BCR-) - Body ground Always 1 MΩ or higher
      JN2-2 (BCR+) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  13. CHECK DTC


    1. Turn the ignition switch to ON.

    2. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    3. Turn the ignition switch off.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1697/82 or B1698/82 is output
      DTC B1692/81 or B1693/81 is output
      DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

      Tech Tips

      Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.


    DTC B1692/81 or B1693/81 is output

    CHECK CONNECTION OF CONNECTORS Click here

    DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

    DTC B1697/82 or B1698/82 is output

  14. CHECK CONNECTION OF CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH and door side airbag sensor LH.

      Result
      Proceed to
      The connectors are properly connected
      The connectors are not properly connected

    The connectors are not properly connected

    CONNECT CONNECTORS PROPERLY

    The connectors are properly connected

  15. CHECK CONNECTORS


    1. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and door side airbag sensor LH.

    2. B0024QGC01
      *1 Side Airbag Sensor Assembly LH
      *2 Door Side Airbag Sensor LH
      *3 Airbag Sensor Assembly
      *4 Floor Wire
      *5 Front Door Wire LH

      Check that the connectors (on the airbag sensor assembly side, side airbag sensor assembly LH side and door side airbag sensor LH side) are not damaged.

      Result
      Proceed to
      The connectors are not deformed or damaged
      The connectors are deformed or damaged

    The connectors are deformed or damaged

    REPLACE FRONT DOOR WIRE LH OR FLOOR WIRE

    The connectors are not deformed or damaged

  16. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT


    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      B0027SLC20
      *1 Door Side Airbag Sensor LH *2 Side Airbag Sensor Assembly LH
      *3 Connector E *4 Connector B
      *5 Service Wire - -
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      		 *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N12-1 (BCL+) - Body ground Ignition switch ON Below 1 V
      N12-2 (BCL-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N12-1 (BCL+) - N12-2 (BCL-) Always Below 1 Ω

    8. Disconnect the service wire from connector E.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N12-1 (BCL+) - N12-2 (BCL-) Always 1 MΩ or higher
      N12-1 (BCL+) - Body ground Always 1 MΩ or higher
      N12-2 (BCL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE Click here

    OK

  17. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B002597C47
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly

      Connect the connectors to the airbag sensor assembly and door side airbag sensor LH.

    2. Interchange the side airbag sensor assembly LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1692/81 or B1693/81 is output
      DTC B1697/82 or B1698/82 is output
      DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

      Tech Tips

      Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors to them.


    DTC B1692/81 or B1693/81 is output

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    DTC B1697/82 or B1698/82 is output

    CHECK DOOR SIDE AIRBAG SENSOR LH Click here

    DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

  18. CHECK FLOOR WIRE


    1. Disconnect the floor wire connector from the front door wire LH.

      B0025CZC15
      *1 Door Side Airbag Sensor LH *2 Side Airbag Sensor Assembly LH
      *3 Front Door Wire LH *4 Floor Wire
      *5 Connector C *6 Connector B
      *7 Service Wire - -
      *a

      Front view of wire harness connector

      (to Front Door Wire LH)

      		 *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N12-1 (BCL+) - Body ground Ignition switch ON Below 1 V
      N12-2 (BCL-) - Body ground Ignition switch ON Below 1 V

    5. Turn the ignition switch off.

    6. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    7. Using a service wire, connect terminals 1 (BCL-) and 2 (BCL+) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N12-1 (BCL+) - N12-2 (BCL-) Always Below 1 Ω

    9. Disconnect the service wire from connector C.

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N12-1 (BCL+) - N12-2 (BCL-) Always 1 MΩ or higher
      N12-1 (BCL+) - Body ground Always 1 MΩ or higher
      N12-2 (BCL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE FLOOR WIRE

  19. CHECK DOOR SIDE AIRBAG SENSOR LH


    1. B00253QC15
      *1 Door Side Airbag Sensor RH
      *2 Side Airbag Sensor Assembly LH

      Interchange the door side airbag sensor LH with RH and connect the connectors to them.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1692/81 or B1693/81 is output
      DTC B1697/82 or B1698/82 is output
      DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

      Tech Tips

      Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.

    9. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    10. Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.


    DTC B1692/81 or B1693/81 is output

    REPLACE DOOR SIDE AIRBAG SENSOR LH Click here

    DTC B1697/82 or B1698/82 is output

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

  20. CHECK CONNECTION OF CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and door side airbag sensor RH.

      Result
      Proceed to
      The connectors are properly connected
      The connectors are not properly connected

    The connectors are not properly connected

    CONNECT CONNECTORS PROPERLY

    The connectors are properly connected

  21. CHECK CONNECTORS


    1. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and door side airbag sensor RH.

    2. B0026S3C03
      *1 Side Airbag Sensor Assembly RH
      *2 Door Side Airbag Sensor RH
      *3 Airbag Sensor Assembly
      *4 Floor Wire
      *5 Front Door Wire RH

      Check that the connectors (on the airbag sensor assembly side, side airbag sensor assembly RH side and door side airbag sensor RH side) are not damaged.

      Result
      Proceed to
      The connectors are not deformed or damaged
      The connectors are deformed or damaged

    The connectors are deformed or damaged

    REPLACE FRONT DOOR WIRE RH OR FLOOR WIRE

    The connectors are not deformed or damaged

  22. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT


    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      B0027SLC16
      *1 Door Side Airbag Sensor RH *2 Side Airbag Sensor Assembly RH
      *3 Connector E *4 Connector B
      *5 Service Wire - -
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      		 *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N13-1 (BCR+) - Body ground Ignition switch ON Below 1 V
      N13-2 (BCR-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N13-1 (BCR+) - N13-2 (BCR-) Always Below 1 Ω

    8. Disconnect the service wire from connector E.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N13-1 (BCR+) - N13-2 (BCR-) Always 1 MΩ or higher
      N13-1 (BCR+) - Body ground Always 1 MΩ or higher
      N13-2 (BCR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE Click here

    OK

  23. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. B00288PC05
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the airbag sensor assembly and door side airbag sensor RH.

    2. Interchange the side airbag sensor assembly RH with LH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1697/82 or B1698/82 is output
      DTC B1692/81 or B1693/81 is output
      DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

      Tech Tips

      Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors to them.


    DTC B1697/82 or B1698/82 is output

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    DTC B1692/81 or B1693/81 is output

    CHECK DOOR SIDE AIRBAG SENSOR RH Click here

    DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

  24. CHECK FLOOR WIRE


    1. Disconnect the floor wire connector from the front door wire RH.

      B0025CZC17
      *1 Door Side Airbag Sensor RH *2 Side Airbag Sensor Assembly RH
      *3 Front Door Wire RH *4 Floor Wire
      *5 Connector C *6 Connector B
      *7 Service Wire - -
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      		 *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N13-1 (BCR+) - Body ground Ignition switch ON Below 1 V
      N13-2 (BCR-) - Body ground Ignition switch ON Below 1 V

    5. Turn the ignition switch off.

    6. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    7. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N13-1 (BCR+) - N13-2 (BCR-) Always Below 1 Ω

    9. Disconnect the service wire from connector C.

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N13-1 (BCR+) - N13-2 (BCR-) Always 1 MΩ or higher
      N13-1 (BCR+) - Body ground Always 1 MΩ or higher
      N13-2 (BCR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  25. CHECK DOOR SIDE AIRBAG SENSOR RH


    1. B00253QC15
      *1 Door Side Airbag Sensor LH
      *2 Side Airbag Sensor Assembly RH

      Interchange the door side airbag sensor RH with LH and connect the connectors to them.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1697/82 or B1698/82 is output
      DTC B1692/81 or B1693/81 is output
      DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

      Tech Tips

      Codes other than DTC B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.

    9. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    10. Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.


    DTC B1697/82 or B1698/82 is output

    REPLACE DOOR SIDE AIRBAG SENSOR RH Click here

    DTC B1692/81 or B1693/81 is output

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output

    USE SIMULATION METHOD TO CHECK Click here