FRONT DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door lock assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Pre-collision system

Click here


  • Power window regulator motor assembly

  • Door window regulator assembly

  • Door glass

  • Door glass run

 Initialize power window control system

  • Jam protection function

  • Power window control system

  • Auto up and down function

  • Remote control function

  • Key-off operation function

  • Catch protection function

Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

  • Fully open the front door glass sub-assembly LH before proceeding with work.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    w/ Curtain Shield Airbag:

    Be sure to read Precaution thoroughly before servicing.

    B0069A2

    for Type B:

    Click here

    for Type C:

    Click here

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    w/ Curtain Shield Airbag:

    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B00693Q

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

    Click here

  4. REMOVE FRONT ARMREST ASSEMBLY LH

    Click here

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side, w/ Power Window)

    Click here

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side, w/ Power Window)

    Click here

  7. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

    Click here

  8. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  10. REMOVE FRONT DOOR SERVICE HOLE COVER LH

    Click here

  11. REMOVE FRONT DOOR GLASS RUN LH

    Click here

  12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

    Click here

  13. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

    Click here

  14. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

    Click here

  15. REMOVE FRONT DOOR LOCK ASSEMBLY LH


    1. B0025SYC01
      *A w/o Double Locking System
      *B w/ Double Locking System
      B0068HS "Torx" Screw
      B006964 Connector

      Disconnect the connector.

    2. Using a T30 "TORX" socket wrench, remove the 3 screws.

    3. B0028NJC01
      *1 Front Door Lock Open Rod LH
      B0069FO Remove in this Direction

      Disconnect the front door lock open rod LH and remove the front door lock assembly LH as shown in the illustration.

  16. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)


    1. B0024EHC01
      B00692L Protective Tape

      Using a thin-bladed screwdriver, detach the claw and clamp and remove the front door lock cover sub-assembly LH from the front door lock assembly LH.

      Tech Tips

      Tape the thin-bladed screwdriver tip before use.

  17. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. B002917C01
      B0069FO Remove in this Direction

      w/o Double Locking System:

      Detach the guide and remove the front door inside locking cable assembly LH from the front door lock assembly LH.

    2. w/ Double Locking System:


      1. B0026WI

        Detach the claw and open the cover.

      2. B0025E1

        Detach the guide and remove the front door lock remote cable assembly LH from the front door lock assembly LH.

  18. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. B00259EC01
      B0069FO Remove in this Direction

      w/o Double Locking System:

      Detach the guide and remove the front door lock remote control cable assembly LH from the front door lock assembly LH.

    2. B0026N7C02
      B0069FO Remove in this Direction

      w/ Double Locking System:

      Detach the guide and remove the front door inside locking cable assembly LH from the front door lock assembly LH.

  19. REMOVE DOOR LOCK WIRING HARNESS SEAL


    1. B00262FC01
      *A w/o Double Locking System
      *B w/ Double Locking System
      B0069FO Remove in this Direction

      Remove the door lock wiring harness seal from the front door lock assembly LH.