Click here

REAR DOOR LOCK(for Double Cab) INSTALLATION

Click here
Click here

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart.

    Click here

Click here

PROCEDURE


  1. Click here

    INSTALL DOOR LOCK WIRING HARNESS SEAL

    Note:

    • When reusing a removed rear door lock assembly LH, replace the door lock wiring harness seal with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

    • Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock assembly LH.


    1. B0027SA

      Install a new door lock wiring harness seal to the rear door lock assembly LH.

  2. Click here

    INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. B0027H7C01
      B0069FO Install in this Direction

      Attach the guide to install the rear door remote control cable assembly LH to the rear door lock assembly LH.

  3. Click here

    INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. B0026VZC01
      B0069FO Install in this Direction

      Attach the guide to install the rear door inside locking cable assembly LH to the rear door lock assembly LH.

  4. Click here

    INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY LH


    1. B0028JY

      Attach the clamp and claw to install the rear door lock cover sub-assembly LH.

  5. Click here

    INSTALL REAR DOOR LOCK ASSEMBLY LH


    1. Apply MP grease to the sliding parts of the rear door lock assembly LH.

    2. B0025ELC01
      *a Release Plate
      B0068HS "Torx" Screw
      B006964 Connector
      B0069FO Install in this Direction

      Insert the rear door lock assembly LH into the rear door outside handle frame sub-assembly LH release plate, and set it to the rear door panel LH.

      Tip:

      Make sure that the rear door outside handle frame sub-assembly LH release plate is securely connected to the rear door lock assembly LH.

    3. Using a T30 "TORX" socket wrench, install the rear door lock assembly LH with the 3 screws.

      5.0 N*m 51 kgf*cm 44 in.*lbf

    4. Connect the connector.

  6. Click here

    INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

    Click here

  7. Click here

    INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

  8. Click here

    INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

    Click here

  9. Click here

    INSTALL REAR DOOR GLASS RUN LH

    Click here

  10. Click here

    INSTALL REAR DOOR SERVICE HOLE COVER LH

    Click here

  11. Click here

    INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  12. Click here

    INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  13. Click here

    INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)

    Click here

  14. Click here

    INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

    Click here

  15. Click here

    INSTALL REAR ARMREST ASSEMBLY LH

    Click here

  16. Click here

    INSTALL REAR DOOR FRAME GARNISH LH

    Click here

  17. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here