Click here

CAN COMMUNICATION SYSTEM(for RHD) Skid Control ECU Communication Stop Mode

Click here
Click here
DTC Code DTC Name
  Skid Control ECU Communication Stop Mode
Click here

DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode

Either condition is met:


  • "Skid Control (ABS/VSC/TRAC)" is not displayed on "CAN Bus Check".

    Click here

  • Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table".

    Click here

  • Power source circuit of brake actuator assembly (skid control ECU)

  • Brake actuator assembly (skid control ECU) ground circuit

  • Brake actuator assembly (skid control ECU) CAN branch wire or connector

  • Brake actuator assembly (skid control ECU)
Figure 2. w/o VSC: B00246YE09
Figure 1. w/VSC:
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds, and then drive the vehicle at a speed of 15 km/h (9 mph) or more for 3 seconds or more.

  • After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

Tip:

  • Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

Click here

PROCEDURE


  1. Click here

    CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)


    1. B00283UC01
      *A w/ VSC
      *B w/o VSC
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

      Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the brake actuator assembly (skid control ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 1. w/ VSC
      Tester Connection Condition Specified Condition
      A4-22 (CANH) - A4-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Table 2. w/o VSC
      Tester Connection Condition Specified Condition
      A3-25 (CANH) - A3-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE SKID CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

  2. Click here

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)


    1. B00283UC05
      *A w/ VSC
      *B w/o VSC
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

      Connect the cable to the negative (-) battery terminal.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Table 3. w/ VSC
      Tester Connection Condition Specified Condition
      A4-38 (+BS) - Body ground Always 11 to 14 V
      A4-13 (BM) - Body ground Always 11 to 14 V
      A4-12 (IG1) - Body ground Ignition switch ON 11 to 14 V
      Table 4. w/o VSC
      Tester Connection Condition Specified Condition
      A3-12 (+BS) - Body ground Always 11 to 14 V
      A3-24 (+BM) - Body ground Always 11 to 14 V
      A3-34 (IG1) - Body ground Ignition switch ON 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 5. w/ VSC
      Tester Connection Condition Specified Condition
      A4-25 (GND1) - Body ground Always Below 1 Ω
      A4-1 (GND2) - Body ground Always Below 1 Ω
      Table 6. w/o VSC
      Tester Connection Condition Specified Condition
      A3-1 (GND1) - Body ground Always Below 1 Ω
      A3-13 (GND2) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    • OK

      REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) w/ VSC:

      REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)Click here

      REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) w/o VSC:

      REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)Click here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR