Click here

CAN COMMUNICATION SYSTEM(for RHD) TERMINALS OF ECU

Click here
Click here
Tip:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


Click here

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note:

      • Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

      • After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

        Click here

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

        Click here

  2. JUNCTION CONNECTOR


    1. B0028MXC66
      *a

      Front view of wire harness connector

      (to No. 1 CAN Junction Connector)

      		 *b for Brake Actuator Assembly (Skid Control ECU)
      *c for Airbag Sensor Assembly *d for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) (w/ VSC)
      *e for DLC3 *f for Combination Meter Assembly
      *g for No. 2 CAN Junction Connector *h for Headlight Leveling ECU Assembly (for LED Headlight)
      *i

      • for Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System)

      • for Air Conditioning Amplifier Assembly (for Manual Air Conditioning System [w/ PTC Heater])

      		 - -

      No. 1 CAN Junction Connector

      No. 1 CAN Junction Connector Wiring Color Connect to
      G67-1 (CANH) B Brake actuator assembly (skid control ECU)
      G67-11 (CANL) W
      G67-2 (CANH) Y Airbag sensor assembly
      G67-12 (CANL) W
      G67-3 (CANH) BE Spiral with sensor cable sub-assembly (steering angle sensor)*1
      G67-13 (CANL) W
      G67-4 (CANH) L DLC3
      G67-14 (CANL) W
      G67-5 (CANH) SB Combination meter assembly
      G67-15 (CANL) W
      G67-6 (CANH) LG No. 2 CAN junction connector
      G67-16 (CANL) W
      G67-8 (CANH) V Headlight leveling ECU assembly*2
      G67-18 (CANL) W
      G67-10 (CANH) GR Air conditioning amplifier assembly*3, *4
      G67-20 (CANL) W

      *1: w/ VSC

      *2: for LED Headlight

      *3: for Automatic Air Conditioning System

      *4: for Manual Air Conditioning System (w/ PTC Heater)

    2. B0028MXC67
      *a

      Front view of wire harness connector

      (to No. 2 CAN Junction Connector)

      		 *b for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System)
      *c for 4 Wheel Drive Control ECU (for 4WD) *d for ECM
      *e for No. 1 CAN Junction Connector *f

      • for Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])

      • for Navigation Receiver Assembly (w/ Navigation System)

      No. 2 CAN Junction Connector

      No. 2 CAN Junction Connector Wiring Color Connect to
      G68-3 (CANH) G Certification ECU (smart key ECU assembly)*1
      G68-13 (CANL) W
      G68-4 (CANH) R 4 wheel drive control ECU*2
      G68-14 (CANL) W
      G68-5 (CANH) B ECM
      G68-15 (CANL) W
      G68-6 (CANH) LG No. 1 CAN junction connector
      G68-16 (CANL) W
      G68-7 (CANH) V

      • Radio and display receiver assembly*3

      • Navigation receiver assembly*4
      G68-17 (CANL) W

      *1: w/ Entry and Start System

      *2: for 4WD

      *3: w/ Audio and Visual System (for Radio and Display Type)

      *4: w/ Navigation System

  3. CHECK DLC3


    1. B0024FUC15
      *a Front view of DLC3

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note:

      • After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

        Click here

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

        Click here

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G8-6 (CANH) - G8-14 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G8-6 (CANH) - G8-4 (CG) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G8-14 (CANL) - G8-4 (CG) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G8-6 (CANH) - G8-16 (BAT) L - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G8-14 (CANL) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  4. Figure 2. for Manual Transmission: B0028HNE02
    Figure 1. for Automatic Transmission: B0028Y0E02

    CHECK ECM (for 2TR-FE)


    1. B0024J1C04
      *a

      Front view of wire harness connector

      (to ECM)

      		 - -

      Disconnect the ECM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G45-13 (CANH) - G45-14 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      G45-13 (CANH) - C52-3 (E1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G45-14 (CANL) - C52-3 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G45-13 (CANH) - G46-3 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G45-14 (CANL) - G46-3 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  5. B0028GVE21

    CHECK ECM (for 1GR-FE)


    1. B00267QC02
      *a

      Front view of wire harness connector

      (to ECM)

      		 - -

      Disconnect the ECM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G88-31 (CANH) - G88-25 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      G88-31 (CANH) - C13-23 (E01) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G88-25 (CANL) - C13-23 (E01) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G88-31 (CANH) - G87-24 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G88-25 (CANL) - G87-24 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  6. B002461E10

    CHECK ECM (for 1GD-FTV, 2GD-FTV)


    1. B0027U0C04
      *a

      Front view of wire harness connector

      (to ECM)

      		 - -

      Disconnect the ECM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G85-17 (CANH) - G85-28 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      G85-17 (CANH) - C60-1 (E1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G85-28 (CANL) - C60-1 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G85-17 (CANH) - G86-1 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G85-28 (CANL) - G86-1 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  7. B0028HNE03

    CHECK ECM (for 1KD-FTV, 2KD-FTV)


    1. B0026DVC01
      *a

      Front view of wire harness connector

      (to ECM)

      		 - -

      Disconnect the ECM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G83-24 (CANH) - G83-23 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      G83-24 (CANH) - C56-7 (E1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G83-23 (CANL) - C56-7 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G83-24 (CANH) - G83-2 (BATT) B - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G83-23 (CANL) - G83-2 (BATT) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  8. B002641E31

    CHECK COMBINATION METER ASSEMBLY


    1. B00270CC58
      *a

      Rear view of wire harness connector

      (to Combination Meter Assembly)

      Disconnect the combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G9-36 (CANH) - G9-35 (CANL) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      G9-36 (CANH) - G9-27 (EP) SB - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G9-35 (CANL) - G9-27 (EP) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G9-36 (CANH) - G9-21 (B) SB - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G9-35 (CANL) - G9-21 (B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  9. Figure 4. Type B: B0026ECE86
    Figure 3. Type A: B0025XAE04

    CHECK AIRBAG SENSOR ASSEMBLY


    1. B0025J5C07
      *a

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)
      *b Front view of DLC3

      Disconnect the airbag sensor assembly connector.

      Type A:Click here

      Type B:Click here

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G42-13 (CANH) - G42-22 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G42-13 (CANH) - G42-25 (E1) Y - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G42-22 (CANL) - G42-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G42-13 (CANH) - G8-16 (BAT) Y - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G42-22 (CANL) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  10. B0025TLE03

    CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/ VSC)


    1. B00270UC08
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

      		 - -

      Disconnect the brake actuator assembly (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      A4-22 (CANH) - A4-10 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      A4-22 (CANH) - A4-25 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      A4-10 (CANL) - A4-25 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      A4-22 (CANH) - A4-13 (BM) B - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      A4-10 (CANL) - A4-13 (BM) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  11. B0027ZIE24

    CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/o VSC)


    1. B00275AC01
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

      Disconnect the brake actuator assembly (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      A3-25 (CANH) - A3-14 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      A3-25 (CANH) - A3-1 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      A3-14 (CANL) - A3-1 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      A3-25 (CANH) - A3-24 (+BM) B - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      A3-14 (CANL) - A3-24 (+BM) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  12. B0024SBE06

    CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (w/ VSC)


    1. B00277RC19
      *a

      Front view of wire harness connector

      (to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])

      Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G21-3 (CANH) - G21-2 (CANL) BE - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G21-3 (CANH) - G21-1 (ESS) BE - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G21-2 (CANL) - G21-1 (ESS) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G21-3 (CANH) - G21-5 (BAT) BE - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G21-2 (CANL) - G21-5 (BAT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  13. B0027WAE05

    CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


    1. B00283GC07
      *a

      Front view of wire harness connector

      (to Certification ECU [Smart Key ECU Assembly])

      		 - -

      Disconnect the certification ECU (smart key ECU assembly) connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G70-40 (CANH) - G70-18 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G70-40 (CANH) - G69-10 (E) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G70-18 (CANL) - G69-10 (E) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G70-40 (CANH) - G69-1 (+B) G - P HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G70-18 (CANL) - G69-1 (+B) W - P LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  14. B002683E03

    CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])


    1. B0026CSC21
      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)

      Disconnect the radio and display receiver assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G37-9 (CANH) - G37-10 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G37-9 (CANH) - G40-7 (GND1) V - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G37-10 (CANL) - G40-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G37-9 (CANH) - G40-4 (+B1) V - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G37-10 (CANL) - G40-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  15. B0028YOE07

    CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)


    1. B0026CSC23
      *a

      Front view of wire harness connector

      (to Navigation Receiver assembly)

      Disconnect the navigation receiver assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G113-9 (CANH) - G113-10 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G113-9 (CANH) - G115-7 (GND1) V - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G113-10 (CANL) - G115-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G113-9 (CANH) - G115-4 (+B1) V - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G113-10 (CANL) - G115-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  16. B00293GE03

    CHECK 4 WHEEL DRIVE CONTROL ECU (for 4WD)


    1. B002483C06
      *a

      Front view of wire harness connector

      (to 4 Wheel Drive Control ECU)

      Disconnect the 4 wheel drive control ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      C39-20 (CANH) - C39-40 (CANL) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      C39-20 (CANH) - C40-10 (GND) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C39-40 (CANL) - C40-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      C39-20 (CANH) - C39-21 (+B) R - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      C39-40 (CANL) - C39-21 (+B) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  17. B0026TQE03

    CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)


    1. B00270CC59
      *a

      Rear view of wire harness connector

      (to Air Conditioning Amplifier Assembly)

      Disconnect the air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G33-11 (TX+) - G33-12 (TX-) GR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G33-11 (TX+) - G33-14 (GND) GR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G33-12 (TX-) - G33-14 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G33-11 (TX+) - G33-21 (B) GR - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G33-12 (TX-) - G33-21 (B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  18. B002800E06

    CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System [w/ PTC Heater])


    1. B0024C8C10
      *a

      Front view of wire harness connector

      (to Air Conditioning Amplifier Assembly)
      *b Front view of DLC3

      Disconnect the air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G77-8 (TX+) - G77-9 (TX-) GR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G77-8 (TX+) - G77-23 (GND) GR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G77-9 (TX-) - G77-23 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G77-8 (TX+) - G8-16 (BAT) GR - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G77-9 (TX-) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
  19. B0024XXE40

    CHECK HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight)


    1. B0025USC07
      *a

      Front view of wire harness connector

      (to Headlight Leveling ECU Assembly)
      *b Front view of DLC3

      Disconnect the headlight leveling ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G80-6 (CANH) - G80-7 (CANL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G80-6 (CANH) - G80-9 (E1) V - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G80-7 (CANL) - G80-9 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G80-6 (CANH) - G8-16 (BAT) V - G HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G80-7 (CANL) - G8-16 (BAT) W - G LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher