FRONT DIFFERENTIAL CARRIER ASSEMBLY COMPONENTS

*A for Manual Transmission - - *1 CLUTCH RELEASE CYLINDER ASSEMBLY *2 NO. 1 ENGINE UNDER COVER *3 NO. 2 ENGINE UNDER COVER *4 POWER STEERING LINK ASSEMBLY *5 STEERING SLIDING YOKE - - Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part - -

*A for Automatic Transmission - - *1 NO. 1 ENGINE UNDER COVER *2 NO. 2 ENGINE UNDER COVER *3 POWER STEERING LINK ASSEMBLY *4 STEERING SLIDING YOKE Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part - -

*1 FRONT DIFFERENTIAL CARRIER ASSEMBLY *2 FRONT DRIVE SHAFT ASSEMBLY LH *3 FRONT DRIVE SHAFT ASSEMBLY RH *4 FRONT PROPELLER SHAFT ASSEMBLY *5 OIL TEMPERATURE SENSOR *6 FRONT DIFFERENTIAL BREATHER HOSE *7 FRONT DRIVE SHAFT HOLE SNAP RING *8 FRONT NO. 1 DIFFERENTIAL SUPPORT *9 FRONT NO. 2 DIFFERENTIAL SUPPORT *10 FRONT NO. 3 DIFFERENTIAL SUPPORT *11 DIFFERENTIAL MOUNT NUT *12 UPPER DIFFERENTIAL MOUNT STOPPER *13 LOWER DIFFERENTIAL MOUNT STOPPER *14 DIFFERENTIAL BREATHER TUBE BRACKET *15 DIFFERENTIAL MOTOR ACTUATOR CONNECTOR *16 OIL TEMPERATURE SENSOR Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part Differential oil MP grease Do not apply lubricants

*A w/ A.D.D. - - *1 DIFFERENTIAL CLUTCH HUB *2 DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY *3 DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH *4 DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH *5 FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR *6 FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH *7 FRONT DIFFERENTIAL TUBE ASSEMBLY *8 SNAP RING *9 NEEDLE BEARING *10 SIDE GEAR SHAFT HOLE SNAP RING *11 DIFFERENTIAL CLUTCH SLEEVE *12 DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY *13 SIDE GEAR INTERMEDIATE SHAFT HOLE SNAP RING - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part MP grease - -

*A w/o A.D.D. - - *1 DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH *2 DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH *3 FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH *4 FRONT DIFFERENTIAL TUBE ASSEMBLY *5 SNAP RING - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part MP grease - -

*1 DIFFERENTIAL DRIVE PINION *2 FRONT DIFFERENTIAL CARRIER OIL SEAL *3 FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER *4 FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER *5 FRONT DIFFERENTIAL OIL STORAGE RING *6 FRONT DRIVE PINION COMPANION FLANGE NUT *7 FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR *8 FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (INNER) *9 FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (OUTER) *10 FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER) *11 FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER) *12 DRIVE PINION PLATE WASHER N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part MP grease Hypoid gear oil LSD *T1 370 (3773, 273) or less - -

*1 DIFFERENTIAL CASE ASSEMBLY *2 DIFFERENTIAL RING GEAR *3 DIFFERENTIAL SIDE BEARING RETAINER *4 FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING *5 FRONT DIFFERENTIAL CARRIER ASSEMBLY *6 FRONT DIFFERENTIAL UNION *7 PLATE WASHER *8 FRONT DIFFERENTIAL CASE BEARING (INNER) *9 FRONT DIFFERENTIAL CASE BEARING (OUTER) *10 FILLER PLUG *11 DRAIN PLUG *12 GASKET *13 STRAIGHT PIN *14 DIFFERENTIAL SIDE GEAR *15 DIFFERENTIAL PINION GEAR *16 DIFFERENTIAL PINION SHAFT *17 DIFFERENTIAL SIDE GEAR THRUST WASHER *18 DIFFERENTIAL PINION GEAR THRUST WASHER *19 DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL LH - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part MP grease Hypoid gear oil Adhesive - - ★ Precoated part - -