STEERING KNUCKLE(for 2WD) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL FRONT INNER AXLE HUB BEARING LH


    1. B0068B1N01

      Using SST and a press, press a new front inner axle hub bearing LH (outer race) into the steering knuckle LH.

      SST
      09527-17011
      09950-60020   ( 09951-00750 )
      09950-70010   ( 09951-07100 )

  2. INSTALL FRONT AXLE HUB HOLE SNAP RING LH


    1. B0069AF

      Using a snap ring pliers, install a new front axle hub hole snap ring LH to the steering knuckle LH.

  3. INSTALL FRONT AXLE HUB OIL SEAL LH


    1. Install a new front inner axle hub bearing LH (outer side inner bearing) to the steering knuckle LH.

    2. B0068WPN01

      Using SST and a press, press a new front axle hub oil seal LH into the steering knuckle LH.

      SST
      09527-17011
      09950-60020   ( 09951-00810 )
      09950-70010   ( 09951-07100 )

    3. Apply MP grease to the lip of the front axle hub oil seal LH.

    4. Install the dust cover with the 3 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  4. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH


    1. B0068Y5N01

      Using SST and a press, press the front axle hub sub-assembly LH into the steering knuckle LH.

      SST
      09950-60010   ( 09951-00600 )
      09527-17011
    2. B0068NMN01

      Using SST and a press, press a new front inner axle hub bearing LH (inner side inner race) into the front axle hub sub-assembly LH.

      SST
      09223-00010
      09527-17011

    3. Install 3 new front axle hub bolts.

      Click here

  5. INSTALL FRONT INNER WHEEL BEARING SPACER LH (w/o ABS)


    1. B0068F7

      Install the front inner wheel bearing spacer LH.

  6. INSTALL FRONT SKID CONTROL ROTOR (w/ ABS)


    1. B0068NF

      Install the front skid control rotor as shown in the illustration.

      Note

      Take care not to scratch the serration of the front skid control rotor.

  7. INSTALL FRONT AXLE SHAFT NUT LH


    1. B00692W

      Using a 36 mm socket wrench, install a new front axle shaft nut LH to the front axle hub sub-assembly LH.

      Torque:
      199 N*m  { 2029 kgf*cm, 147 ft.*lbf }
    2. B0068K8

      Using a chisel and hammer, stake the front axle shaft nut LH.

      Note

      Do not scratch the serration of the front skid control rotor.

  8. INSTALL KNUCKLE GREASE RETAINER CAP LH


    1. B006915C01
      *a Clearance

      Using SST and a hammer, tap the knuckle grease retainer cap LH.

      SST
      09527-17011
      09950-60020   ( 09951-00910 )
      09950-70010   ( 09951-07150 )
      Standard clearance
      0.2 mm (0.0079 in.) or less

      Note

      Do not damage the knuckle grease retainer cap LH.

  9. CONNECT FRONT UPPER SUSPENSION ARM ASSEMBLY LH


    1. Connect the front upper suspension arm assembly LH to the steering knuckle LH with a new nut.

      Torque:
      110 N*m  { 1122 kgf*cm, 81 ft.*lbf }

    2. Install a new clip.

      Note

      If the holes for the clip are not aligned, tighten the nut an additional 60°.

  10. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH

    B0068E2

    1. Connect the front lower No. 1 suspension arm LH to the steering knuckle LH with the 2 bolts.

      Torque:
      160 N*m  { 1632 kgf*cm, 118 ft.*lbf }

  11. CONNECT TIE ROD END SUB-ASSEMBLY LH

    Click here

  12. INSTALL FRONT DISC

    Click here

  13. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH

    Click here

  14. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH

    Click here

  15. CONNECT FRONT FLEXIBLE HOSE

    Click here

  16. CONNECT FRONT SPEED SENSOR LH (w/ ABS)


    1. B0069A0

      Install the front speed sensor LH with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Make sure there are no pieces of iron or other foreign matter attached to the front speed sensor LH tip.

      • While inserting the front speed sensor LH into the knuckle hole, do not strike or damage the sensor tip.

      • After installing the front speed sensor LH, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

      • When installing the front speed sensor LH, do not twist the wire harness.

    2. Install the harness clamp to the steering knuckle with the bolt.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

      Note


      • When installing the harness clamp, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    3. B0068CM

      Install the harness clamp to the front lower arm bracket with the bolt.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

      Note


      • When installing the harness clamp, do not twist the wire harness.

      • Make sure the harness clamp rotation stopper touches the installation position.

    4. Install the harness clamp to the front absorber bracket with the bolt.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

      Note


      • When installing the harness clamp, do not twist the wire harness.

      • Make sure the harness clamp rotation stopper touches the installation position.

  17. INSTALL FRONT WHEEL

    Click here

  18. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  19. CHECK ABS SPEED SENSOR SIGNAL (w/ ABS)


    1. w/ VSC:

      Click here

    2. w/o VSC:

      Click here