Click here

FRONT AXLE HUB(for 4WD and Pre-Runner) INSTALLATION

Click here
Click here Click here

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here

PROCEDURE


  1. Click here

    INSTALL PLUG (for Pre-Runner)


    1. B0024VUN01

      Using SST and a hammer, install a new plug.

      09950-60010 09951-00450
      09950-70010 09951-07100
  2. Click here

    INSTALL FRONT AXLE HUB OIL SEAL LH


    1. B0026WP

      Using a brass bar and hammer, tap in a new front axle hub oil seal LH.

  3. Click here

    INSTALL FRONT AXLE HUB INNER BEARING LH (for 4WD)


    1. B0024Q0N01

      Using SST and a press, press a new front axle hub inner bearing LH into the front axle hub sub-assembly LH.

      09649-17010
      Note:

      Insert 4 bolts into the bearing before installing the bearing to the front axle hub sub-assembly LH.

  4. Click here

    INSTALL FRONT AXLE HUB INNER BEARING LH (for Pre-Runner)


    1. B00284FN01

      Using SST and a press, press a new front axle hub inner bearing LH into the front axle hub sub-assembly LH.

      09649-17010
      Note:

      Insert 4 bolts into the bearing before installing the bearing to the front axle hub sub-assembly LH.

    2. B0024AHN01

      Using SST, install a new adjusting nut.

      09607-26010
      274 N*m 2794 kgf*cm 202 ft.*lbf
    3. B0028QRN03

      Using SST and a hammer, stake the adjusting nut.

      09930-00010
  5. Click here

    INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH (for 4WD)


    1. Apply MP grease to a new O-ring.

    2. Install the O-ring to the axle hub.

    3. Install the dust cover and front axle hub sub-assembly LH to the steering knuckle LH with the 4 bolts.

      Specified tightening torque
      80 N*m 816 kgf*cm 59 ft.*lbf
      Tip:

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using a ball joint lock nut wrench (fulcrum length of 149 mm (5.866 in.)) + torque wrench (fulcrum length of 380 mm (14.961 in.)): 57.5 N*m (586 kgf*cm, 42 ft.*lbf).

  6. Click here

    INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH (for Pre-Runner)


    1. B0026ZP

      Apply MP grease to a new O-ring.

    2. Install the O-ring to the axle hub.

    3. Install the dust cover and front axle hub sub-assembly LH to the steering knuckle LH with the 4 bolts.

      Specified tightening torque
      80 N*m 816 kgf*cm 59 ft.*lbf
      Tip:

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using a ball joint lock nut wrench (fulcrum length of 149 mm (5.866 in.)) + torque wrench (fulcrum length of 380 mm (14.961 in.)): 57.5 N*m (586 kgf*cm, 42 ft.*lbf).

  7. Click here

    INSTALL FRONT AXLE SHAFT NUT LH (for 4WD)


    1. Clean the threaded parts on the drive shaft and front axle shaft nut LH using a non-residue solvent.

    2. Install the front axle shaft nut LH.

      235 N*m 2396 kgf*cm 173 ft.*lbf

    3. Install the adjusting cap and a new cotter pin.

      Note:

      If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.

  8. Click here

    INSTALL FRONT AXLE HUB GREASE CAP LH (for 4WD)


    1. Install a new front axle hub grease cap LH to the front axle hub sub-assembly LH.

  9. Click here

    INSTALL FRONT DISC

    Click here

  10. Click here

    INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH

    Click here

  11. Click here

    CONNECT FRONT SPEED SENSOR LH

    Click here

  12. Click here

    INSTALL FRONT WHEEL

    Click here

  13. Click here

    CHECK ABS SPEED SENSOR SIGNAL


    1. w/ VSC:

      Click here

    2. w/o VSC:

      Click here