PROPELLER SHAFT ASSEMBLY(for TSAM Made) COMPONENTS
ILLUSTRATION
| *A | for 2WD and Pre-Runner | - | - |
| *1 | PROPELLER SHAFT GUARD | *2 | PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY |
| *3 | DIFFERENTIAL TORSIONAL DAMPER | - | - |
| *a | for Differential Type BD22 | *b | for Differential Type BD20 |
| *c | for RC60 and RC61 | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |  |
N*m (kgf*cm, ft.*lbf): Specified torque |
 |
Do not apply lubricants | - | - |
ILLUSTRATION
| *A | for 4WD | - | - |
| *1 | PROPELLER SHAFT GUARD | *2 | PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| |
Do not apply lubricants | - | - |
ILLUSTRATION
| *A | for 2WD and Pre-Runner (Vehicle Type A) | - | - |
| *1 | CENTER NO. 1 SUPPORT BEARING ASSEMBLY | *2 | UNIVERSAL JOINT SPIDER ASSEMBLY |
| *3 | SNAP RING | *4 | SPIDER BEARING |
| *5 | SLEEVE YOKE | *6 | CENTER YOKE |
| *7 | FLANGE YOKE | *8 | PROPELLER SHAFT |
| *9 | INTERMEDIATE SHAFT | *10 | LOCK NUT |
| *11 | WASHER | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
 |
Lithium base chassis grease NLGI No. 2 | - | - |
ILLUSTRATION
| *A | for 2WD and Pre-Runner (Vehicle Type B) | - | - |
| *1 | CENTER NO. 1 SUPPORT BEARING ASSEMBLY | *2 | UNIVERSAL JOINT SPIDER ASSEMBLY |
| *3 | SNAP RING | *4 | SPIDER BEARING |
| *5 | GREASE NIPPLE | *6 | SLEEVE YOKE |
| *7 | CENTER YOKE | *8 | FLANGE YOKE |
| *9 | PROPELLER SHAFT | *10 | INTERMEDIATE SHAFT |
| *11 | LOCK NUT | *12 | WASHER |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| |
Lithium base chassis grease NLGI No. 2 | - | - |
ILLUSTRATION
| *A | for 4WD | - | - |
| *1 | CENTER NO. 1 SUPPORT BEARING ASSEMBLY | *2 | REAR SLIDING SHAFT BOOT |
| *3 | UNIVERSAL JOINT SPIDER ASSEMBLY | *4 | SNAP RING |
| *5 | SPIDER BEARING | *6 | GREASE NIPPLE |
| *7 | FLANGE YOKE | *8 | SLEEVE YOKE |
| *9 | CENTER YOKE | *10 | PROPELLER SHAFT |
| *11 | INTERMEDIATE SHAFT | *12 | LOCK NUT |
| *13 | WASHER | *14 | CLAMP |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| |
Lithium base chassis grease NLGI No. 2 |  |
MP grease |