Click here

TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM, Diagnostic DTC:P17AA

Click here
Click here
DTC Code DTC Name
P17AA Transfer Shift Motor Control Circuit High
Click here

DESCRIPTION

This DTC is output when a short to B+ in the transfer shift motor and A.D.D. shift motor* drive circuit is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area
P17AA Transfer Shift Motor Control Circuit High

  • Diagnosis Condition: Directly after or while the ignition switch is turned to ON (transfer shift motor not operating)

  • Malfunction Status: Short to B+ in the transfer shift motor and A.D.D. shift motor* drive circuits

  • Malfunction Time: 0.5 seconds or more (after the ignition switch is turned to ON, 0.05 seconds or more)

  • Other: 1 trip detection logic

  • Wire harness and connector

  • 4 wheel drive control ECU

  • Transfer shift actuator assembly

  • A.D.D. actuator (differential motor actuator assembly)*

Click here

WIRING DIAGRAM

Refer to DTC P17A9.

Click here

Click here

PROCEDURE


  1. Click here

    CHECK ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR AND A.D.D. SHIFT MOTOR)


    1. Disconnect the C40 4 wheel drive control ECU connector.

    2. B0068GHC07
      *A w/ A.D.D. Actuator
      *a

      Front view of wire harness connector

      (to 4 Wheel Drive Control ECU)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Table 1. Transfer shift actuator assembly side:
      Tester Connection Condition Specified Condition
      C40-8 (TM1) or C40-7 (TM2) - Body ground Ignition switch ON Below 1 V
      Table 2. A.D.D. actuator (differential motor actuator assembly) side (w/ A.D.D. Actuator):
      Tester Connection Condition Specified Condition
      C40-2 (DM1) or C40-6 (DM2) - Body ground Ignition switch ON Below 1 V
      Result
      Result Proceed to
      OK A
      NG (transfer shift actuator assembly side) B
      NG (A.D.D. actuator (differential motor actuator assembly) side) (w/ A.D.D. Actuator) C

  2. Click here

    CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)


    1. Disconnect the C40 4 wheel drive control ECU connector.

    2. Disconnect the C41 transfer shift actuator assembly connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      C40-8 (TM1) or C41-2 (TM1) - Body ground Ignition switch ON Below 1 V
      C40-7 (TM2) or C41-1 (TM2) - Body ground Ignition switch ON Below 1 V
      Result
      Proceed to
      OK
      NG

    • OK

      REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLYClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. Click here

    CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY - BODY GROUND)


    1. Disconnect the C40 4 wheel drive control ECU connector.

    2. Disconnect the C7 A.D.D. actuator (differential motor actuator assembly) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      C40-2 (DM1) or C7-1 (DM1) - Body ground Ignition switch ON Below 1 V
      C40-6 (DM2) or C7-2 (DM2) - Body ground Ignition switch ON Below 1 V
      Result
      Proceed to
      OK
      NG

    • OK

      REPLACE DIFFERENTIAL MOTOR ACTUATOR ASSEMBLYClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR