AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) Illumination Circuit

DESCRIPTION

The radio receiver assembly and steering pad switch assembly illuminates when the headlight dimmer switch is in the tail or head position.

WIRING DIAGRAM

B00287IE04

CAUTION / NOTICE / HINT

Note

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

for Type A: Click here

for Type B: Click here

PROCEDURE


  1. CHECK ILLUMINATION


    1. Check if the illumination for the radio receiver assembly, steering pad switch assembly or others (hazard switch etc.) comes on when the turn signal switch is turned to the head or tail position.

      Result
      Result Proceed to
      Illumination comes on for all components except steering pad switch assembly. A
      Illumination comes on for all components except radio receiver assembly. B
      No illumination comes on (radio receiver assembly, steering pad switch, hazard switch etc.). C

    B
    C
    A
  2. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Remove the steering pad switch assembly.

      Click here

    2. Inspect the steering pad switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG
    OK
  3. CHECK VEHICLE CONDITION


    1. Check the vehicle condition.

      Result
      Result Proceed to
      w/ VSC A
      w/o VSC B

    B
    A
  4. INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    1. Remove the spiral with sensor cable sub-assembly.

      Click here

    2. Inspect the spiral with sensor cable sub-assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG
    OK
  5. CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)


    1. B0024IMC18
      *a

      Front view of wire harness connector

      (to Spiral with Sensor Cable Sub-assembly)

      Disconnect the spiral with sensor cable sub-assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G4-13 (IL+2) - Body ground Headlight dimmer switch in tail or head position 11 to 14 V
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G4-3 (EAU) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK
    NG
  6. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. Remove the spiral cable sub-assembly.

      Click here

    2. Inspect the spiral cable sub-assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG
    OK
  7. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)


    1. B0024IMC18
      *a

      Front view of wire harness connector

      (to Spiral Cable Sub-assembly)

      Disconnect the spiral cable sub-assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G4-13 (IL+2) - Body ground Headlight dimmer switch in tail or head position 11 to 14 V
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G4-3 (EAU) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK
    NG
  8. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY, BATTERY AND BODY GROUND)


    1. Disconnect the G118 and G119 radio receiver assembly connectors.

    2. Disconnect the G9 combination meter assembly connector*.


      • *: for TFT Display Type

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G118-10 (ILL+) - Body ground Headlight dimmer switch in tail or head position 11 to 14 V
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for TFT Display Type
      Tester Connection Condition Specified Condition
      G119-5 (ILL-) - G9-21 (ILL-) Always Below 1 Ω
      G119-5 (ILL-) or G9-21 (ILL-) - Body ground Always 10 kΩ or higher
      except TFT Display Type
      Tester Connection Condition Specified Condition
      G119-5 (ILL-) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK
    NG