PARKING BRAKE CABLE(for 4WD and Pre-Runner) REMOVAL

PROCEDURE

1. REMOVE REAR WHEEL

   Click here

2. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

   Click here

3. REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY

   Click here

4. REMOVE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (w/ Smart Entry and Start System)

   Click here

5. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

   
   

   1. for Single Cab:

      Click here

6. REMOVE FRONT SEAT ASSEMBLY (for Bench Seat Type)

   
   

   1. for Single Cab:

      Click here

7. REMOVE REAR SEAT ASSEMBLY

   
   

   1. for Smart Cab (w/ Rear Seat Assembly):

      Click here

   2. for Double Cab:

      
      

      1. for Seat Cushion 60/40 Split Type:

         Click here

      2. for Seat Cushion Bench Type:

         Click here

8. REMOVE BACK PANEL TRIM (for Smart Cab)

   Click here

9. REMOVE FRONT DOOR SCUFF PLATE LH

   
   

   1. for Single Cab:

      Click here

   2. for Smart Cab:

      Click here

10. REMOVE FRONT DOOR SCUFF PLATE RH

    
    

    1. for Single Cab:

       Click here

    2. for Smart Cab:

       Click here

11. REMOVE REAR DOOR SCUFF PLATE LH (for Double Cab)

    Click here

12. REMOVE REAR DOOR SCUFF PLATE RH (for Double Cab)

    Click here

13. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

    
    

    1. for Smart Cab:

       Click here

    2. for Double Cab:

       Click here

14. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

    
    

    1. for Smart Cab:

       Tech Tips

       Use the same procedure described for the LH side.

    2. for Double Cab:

       Tech Tips

       Use the same procedure described for the LH side.

15. REMOVE LOWER QUARTER TRIM PANEL LH

    
    

    1. for Single Cab:

       Click here

    2. for Smart Cab:

       Click here

    3. for Double Cab:

       Click here

16. REMOVE LOWER QUARTER TRIM PANEL RH

    
    

    1. for Single Cab:

       Click here

    2. for Smart Cab:

       Click here

    3. for Double Cab:

       Click here

17. REMOVE LUGGAGE COMPARTMENT SIDE COVER LH (for Smart Cab)

    Click here

18. REMOVE LUGGAGE COMPARTMENT SIDE COVER RH (for Smart Cab)

    Click here

19. REMOVE INTERMEDIATE LEVER PROTECTOR

    
    

    1. Partially remove the floor carpet.

       Tech Tips

       It is not necessary to fully remove the floor carpet. Partially remove it so that the intermediate lever protector can be removed in a later step.

    2. Remove the 3 bolts and intermediate lever protector with No. 2 console box mounting bracket.

       

       *A

       for Single Cab

       *B

       except Single Cab

20. REMOVE NO. 2 CONSOLE BOX MOUNTING BRACKET

    
    

    1. Remove the 2 bolts and No. 2 console box mounting bracket from the intermediate lever protector.

       

       *A

       for Single Cab

       *B

       except Single Cab

21. REMOVE PARKING BRAKE CABLE HEAT INSULATOR

    
    

    1. 

       Remove the 2 bolts and parking brake cable heat insulator.

22. REMOVE PROPELLER SHAFT ASSEMBLY

    
    

    1. for TSAM Made:

       Click here

    2. for TMT Made:

       Click here

23. REMOVE FUEL TANK

    
    

    1. 1GR-FE:

       Click here

    2. 2KD-FTV:

       Click here

    3. 1GD-FTV:

       Click here

    4. 2GD-FTV:

       Click here

    5. 2TR-FE:

       Click here

    6. 5L-E:

       Click here

24. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY

    
    

    1. Remove the 2 bolts (labeled A).

       

       *1	No. 1 Parking Brake Cable Assembly	*2	No. 2 Parking Brake Cable Assembly
       *3	No. 3 Parking Brake Cable Assembly	*4	Parking Brake Equalizer Sub-assembly
       *5	Cable Support Bracket	-	-

    2. Remove the clip and pin from the No. 3 parking brake cable assembly.

    3. Disconnect the No. 1 parking brake cable assembly from the No. 3 parking brake cable assembly.

    4. Disconnect the No. 1 parking brake cable assembly from the parking brake equalizer sub-assembly.

    5. Disconnect the No. 1 parking brake cable assembly from the cable support bracket.

    6. Remove the No. 1 parking brake cable assembly from inside the vehicle.

    7. Remove the bolt (labeled B) and cable support bracket.

25. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY

    
    

    1. Disconnect the No. 2 parking brake cable assembly from the parking brake shoe lever.

       Tech Tips

       Refer to the procedures up to the removal of the brake shoe.

       Click here

    2. 

       Remove the 2 bolts and disconnect the No. 2 parking brake cable assembly from the backing plate.

    3. Disconnect the No. 2 parking brake cable assembly from the parking brake equalizer sub-assembly.

       

       *1

       No. 2 Parking Brake Cable Assembly

       *2

       Parking Brake Equalizer Sub-assembly

    4. Remove the 4 bolts and No. 2 parking brake cable assembly.

26. REMOVE PARKING BRAKE EQUALIZER SUB-ASSEMBLY

    
    

    1. 

       Remove the 2 bolts and parking brake equalizer sub-assembly.

27. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

    
    

    1. Disconnect the No. 3 parking brake cable assembly from the parking brake shoe lever.

       Tech Tips

       Refer to the procedures up to the removal of the brake shoe.

       Click here

    2. 

       Remove the 2 bolts and disconnect the No. 3 parking brake cable assembly from the backing plate.

    3. Remove the clip.

       

       *1

       No. 3 Parking Brake Cable Assembly

       -

       -

    4. Remove the 3 bolts, nut and No. 3 parking brake cable assembly.