Click here

FRONT DISC BRAKE PAD(for 4WD and Pre-Runner) REPLACEMENT

Click here
Click here Click here

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Note:

After replacing the disc brake pads, the clearance between the disc brake pads and front discs becomes larger and the brake pedal feel becomes softer. Therefore, after replacing the disc brake pads, depress the brake pedal several times and check the clearance and brake pedal feel.

Click here

PROCEDURE


  1. Click here

    REMOVE FRONT WHEEL

    Click here

  2. Click here

    DRAIN BRAKE FLUID

    Note:

    Wash off brake fluid immediately if it comes in contact with any painted surface.

  3. Click here

    REMOVE FRONT DISC BRAKE ANTI-RATTLE SPRING


    1. for 15 inch Front Disc Brake:


      1. B00287NC01
        *1 Disc Brake Pad Guide Pin
        *2 Pin Hold Clip
        *3 Front Disc Brake Anti-rattle Spring

        Remove the pin hold clip and 2 disc brake pad guide pins.

      2. Remove the front disc brake anti-rattle spring.

        Note:

        The front disc brake anti-rattle spring can be reused if it has sufficient rebound; no deformation, cracks or wear; and has all rust, dirt and foreign matter cleaned off.

    2. for 16 inch Front Disc Brake:


      1. B0028HUC01
        *1 Disc Brake Pad Guide Pin
        *2 Pin Hold Clip
        *3 Front Disc Brake Anti-rattle Spring

        Remove the 2 pin hold clips and 2 disc brake pad guide pins.

      2. Remove the front disc brake anti-rattle spring.

        Note:

        The front disc brake anti-rattle spring can be reused if it has sufficient rebound; no deformation, cracks or wear; and has all rust, dirt and foreign matter cleaned off.

  4. Click here

    REMOVE FRONT DISC BRAKE PAD


    1. Remove the 2 front disc brake pads from the disc brake cylinder assembly LH.

  5. Click here

    REMOVE FRONT ANTI-SQUEAL SHIM KIT


    1. Remove the 2 No. 1 anti-squeal shims and 2 No. 2 anti-squeal shims from each pad.

  6. Click here

    INSTALL FRONT ANTI-SQUEAL SHIM KIT


    1. B002665C01
      *1 Front Disc Brake Pad
      *2 No. 1 Anti-squeal Shim
      *3 No. 2 Anti-squeal Shim
      B0068HS Disc Brake Grease

      Apply disc brake grease to both sides of each No. 1 anti-squeal shim.

    2. Install the No. 1 anti-squeal shims and No. 2 anti-squeal shims to each pad.

      Note:

      • When replacing worn front disc brake pads, the anti-squeal shims must be replaced together with the front disc brake pads.

      • Install the anti-squeal shims in the correct positions and directions as shown in the illustration.

  7. Click here

    INSTALL FRONT DISC BRAKE PAD


    1. B0028KKC01
      B0069FO Expand

      Using SST, push back the front disc brake piston.

      Note:

      Do not forcibly install the piston into the disc brake cylinder assembly LH.

      09719-77020

    2. Install the 2 front disc brake pads to the disc brake cylinder assembly LH.

      Note:

      Make sure there is no oil or grease on the friction surface of the front disc brake pads and front disc.

  8. Click here

    INSTALL FRONT DISC BRAKE ANTI-RATTLE SPRING


    1. for 15 inch Front Disc Brake:


      1. Install the 2 disc brake pad guide pins and front disc brake anti-rattle spring.

        Tip:

        Install the front disc brake anti-rattle spring together with the disc brake pad guide pin on the bottom side.

      2. Install the pin hold clip.

    2. for 16 inch Front Disc Brake:


      1. Install the 2 disc brake pad guide pins and front disc brake anti-rattle spring.

        Tip:

        Install the front disc brake anti-rattle spring together with the disc brake pad guide pin on the bottom side.

      2. Install the 2 pin hold clips.

        Note:

        When installing the pin hold clip, be sure to install the pin hold clip with the handle facing the center of the vehicle.

    3. Depress the brake pedal several times.

  9. Click here

    ADD BRAKE FLUID


    1. w/ VSC:

      Click here

    2. w/o VSC:

      Click here

  10. Click here

    INSTALL FRONT WHEEL

    Click here