NAVIGATION SYSTEM Steering Pad Switch Circuit

DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the navigation receiver assembly cannot be operated using the steering pad switch assembly, and also the navigation receiver assembly itself cannot function.

WIRING DIAGRAM

B0028EDE03

CAUTION / NOTICE / HINT

Note


  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

    for Type A: Click here

    for Type B: Click here

  • Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

    Click here

PROCEDURE


  1. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Remove the steering pad switch assembly.

      Click here

    2. Inspect the steering pad switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

  2. CHECK VEHICLE CONDITION


    1. Check the vehicle condition.

      Result
      Result Proceed to
      w/ VSC A
      w/o VSC B

    B

    INSPECT SPIRAL CABLE SUB-ASSEMBLY Click here

    A

  3. INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    1. Remove the spiral with sensor cable sub-assembly.

      Click here

    2. Inspect the spiral with sensor cable sub-assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)


    1. Disconnect the G113 navigation receiver assembly connector.

    2. Disconnect the G4 spiral with sensor cable sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G113-21 (SW1) - G4-6 (AU1) Always Below 1 Ω
      G113-23 (SWG) - G4-3 (EAU) Always Below 1 Ω
      G113-22 (SW2) - G4-5 (AU2) Always Below 1 Ω
      G113-21 (SW1) - Body ground Always 10 kΩ or higher
      G113-23 (SWG) - Body ground Always 10 kΩ or higher
      G113-22 (SW2) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. Remove the spiral cable sub-assembly.

      Click here

    2. Inspect the spiral cable sub-assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)


    1. Disconnect the G113 navigation receiver assembly connector.

    2. Disconnect the G4 spiral cable sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G113-21 (SW1) - G4-6 (AU1) Always Below 1 Ω
      G113-23 (SWG) - G4-3 (EAU) Always Below 1 Ω
      G113-22 (SW2) - G4-5 (AU2) Always Below 1 Ω
      G113-21 (SW1) - Body ground Always 10 kΩ or higher
      G113-23 (SWG) - Body ground Always 10 kΩ or higher
      G113-22 (SW2) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR