Click here

STOP AND START SYSTEM, Diagnostic DTC:P0562

Click here
Click here
DTC Code DTC Name
P0562 System Voltage Low
Click here

DESCRIPTION

The engine stop and start ECU monitors +B terminal voltage while the engine is stopped by stop and start control. If the voltage drops below the specified level, the engine stop and start ECU stores DTC P0562 and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0562 System Voltage Low

Both of the following conditions are met for 2 seconds or more (1 trip detection logic):


  • +B terminal voltage is 9 V or less.

  • Engine stopped by stop and start control

  • Battery

  • Wire harness or connector

  • Instrument panel junction block assembly (EFI-MAIN NO. 1, EFI-MAIN NO. 2 relay)

  • Engine stop and start ECU

 Blinks DTC stored
Click here

CONFIRMATION DRIVING PATTERN

Tip:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click here


Click here
  1. Tip:

    • If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

      In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

    • If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

      If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

    • After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

      If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

    • Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.

    CONFIRMATION AFTER TROUBLESHOOTING


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Click here


      1. Powertrain > Stop and Start > Clear DTCs


    4. Start the engine and warm it up.

    5. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    6. for Automatic Transmission:

      Depress the brake pedal and stop the vehicle.

      for Manual Transmission:

      Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

    7. Keep the engine stopped by stop and start control for 1 second or more. (for Automatic Transmission: Keep the shift lever in D.)

    8. for Automatic Transmission:

      Release the brake pedal with the shift lever in D to start the engine.

      for Manual Transmission:

      Depress the clutch pedal and start the engine.

      Tip:

      If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.

    9. Check that DTCs are not output.

      Click here


      1. Powertrain > Stop and Start > Trouble Codes


  2. Tip:

    • If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

      In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

    • If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

      If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

    • After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

      If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

    STOP AND START SYSTEM OPERATION CHECK


    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    4. for Automatic Transmission:

      Depress the brake pedal and stop the vehicle.

      for Manual Transmission:

      Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

    5. Allow the engine to stop by stop and start control. (for Automatic Transmission: Keep the shift lever in D.)

    6. for Automatic Transmission:

      Release the brake pedal with the shift lever in D to start the engine.

      for Manual Transmission:

      Depress the clutch pedal and start the engine.

Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

    Click here

  • for Automatic Transmission:

    When the engine stop and start ECU is replaced, check the electromagnetic oil pump.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click here

Click here

PROCEDURE


  1. Click here

    READ VALUE USING GTS (BATTERY VOLTAGE)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

      Tip:

      Do not start the engine.

    3. Turn the GTS on.

    4. Turn off all electrical systems.

    5. Enter the following menus: Powertrain / Stop and Start / Data List / Battery Voltage.


      1. Powertrain > Stop and Start > Data List
        Tester Display
        Battery Voltage




    6. Read the battery voltage displayed on the GTS screen.

      Result
      Result Proceed to
      9 to 14 V A
      Below 9 V B

  2. Click here

    INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 1, EFI-MAIN NO. 2 RELAY)


    1. Inspect the instrument panel junction block assembly (EFI-MAIN NO. 1, EFI-MAIN NO. 2 relay).

      Click here

      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

  3. Click here

    CHECK HARNESS AND CONNECTOR (+B TERMINAL VOLTAGE)


    1. B0024ANC90
      *a

      Component with harness connected

      (Engine Stop and Start ECU)

      		 - -

      Turn the ignition switch to ON.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G126-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
      Result
      Proceed to
      OK
      NG

    • OK

      REPLACE ENGINE STOP AND START ECUClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR