OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

  • B0068VK

    To prevent burns, do not remove the oil pan drain plug and oil filter sub-assembly while the engine is hot.

PROCEDURE


  1. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

  2. DRAIN ENGINE OIL

    CAUTION:

    To prevent burns, do not remove the oil pan drain plug while the engine is hot.


    1. Remove the oil filler cap sub-assembly.

    2. Remove the oil pan drain plug and gasket, and drain the oil into a container.

      Tech Tips

      Clean the crossmember after replacing the engine oil, as oil will make contact with it.

    3. Clean and install the oil pan drain plug and a new gasket.

      Torque:
      37.5 N*m  { 382 kgf*cm, 28 ft.*lbf }

  3. REMOVE OIL FILTER SUB-ASSEMBLY

    CAUTION:

    To prevent burns, do not remove the oil filter sub-assembly while the engine is hot.


    1. A01WAQBN01

      Using SST, remove the oil filter sub-assembly.

      SST
      09228-07501

      Tech Tips


      • Before removing the oil filter sub-assembly, place cloth where the oil may splash.

      • Use a container to catch the draining engine oil.

  4. INSTALL OIL FILTER SUB-ASSEMBLY


    1. Check and clean the oil filter sub-assembly installation surface.

    2. Apply clean engine oil to the gasket of a new oil filter sub-assembly.

    3. A01W82WC01
      B0068HS 3/4 Turn

      Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.

    4. Using SST, tighten the oil filter sub-assembly.

      SST
      09228-07501

      1. Depending on the work space available, choose from the following.

        If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

        Torque:
        17.2 N*m  { 175 kgf*cm, 13 ft.*lbf }

        If enough space is not available to use a torque wrench, tighten the oil filter sub-assembly a 3/4 turn by hand or use a common wrench.

  5. ADD ENGINE OIL


    1. Add new engine oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil

      0W-20

      5W-20

      5W-30

      10W-30
      API grade SL, SM or SN multigrade engine oil

      15W-40

      20W-50*

      Note

      *: This grade of engine oil cannot be used for Euro IV or higher.

      Standard Capacity
      Item Capacity
      Drain and refill without oil filter sub-assembly change 5.3 liters (5.6 US qts, 4.7 Imp. qts)
      Drain and refill with oil filter sub-assembly change 5.6 liters (5.9 US qts, 4.9 Imp. qts)
      Dry fill 6.3 liters (6.7 US qts, 5.5 Imp. qts)

    2. Install the oil filler cap sub-assembly.

  6. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.

  7. CHECK ENGINE OIL LEVEL

    Click here

  8. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

    Click here