ENGINE ASSEMBLY COMPONENTS

*A w/o Secondary Air Injection System *B w/ Secondary Air Injection System *1 AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE *2 AIR CLEANER CASE SUB-ASSEMBLY *3 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY *4 HOOD SUB-ASSEMBLY *5 INTAKE AIR CONNECTOR *6 NO. 1 AIR HOSE *7 NO. 2 PCV HOSE *8 VACUUM HOSE N*m (kgf*cm, ft.*lbf): Specified torque - -

*A for 2WD *B for 4WD *C w/o Secondary Air Injection System *D w/ Secondary Air Injection System *1 FRONT FENDER SEAL LH *2 FRONT FENDER SEAL RH *3 FRONT UPPER FENDER APRON SEAL LH *4 FRONT UPPER FENDER APRON SEAL RH *5 NO. 1 ENGINE UNDER COVER *6 NO. 1 ENGINE UNDER COVER ASSEMBLY *7 NO. 1 RADIATOR AIR GUIDE *8 NO. 2 ENGINE UNDER COVER *9 NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

*A w/ Secondary Air Injection System *B for Automatic Transmission *1 AIR PUMP INLET *2 FAN SHROUD *3 NO. 1 OIL COOLER INLET HOSE *4 NO. 1 OIL COOLER OUTLET HOSE *5 RADIATOR ASSEMBLY *6 RADIATOR HOSE INLET *7 RADIATOR HOSE OUTLET *8 RADIATOR RESERVOIR *9 RADIATOR DRAIN COCK PLUG *10 CLAMP *11 FAN AND GENERATOR V BELT *12 FAN PULLEY *13 FLUID COUPLING FAN *14 GROMMET *15 O-RING *16 WIRE HARNESS N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

*1 COOLER COMPRESSOR ASSEMBLY *2 ENGINE OIL LEVEL DIPSTICK *3 ENGINE OIL LEVEL DIPSTICK GUIDE *4 VANE PUMP ASSEMBLY *5 O-RING *6 STUD BOLT *7 HEATER WATER OUTLET HOSE *8 HEATER WATER INLET HOSE Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part - -

*A for Manual Transmission - - *1 STARTER ASSEMBLY *2 CLUTCH RELEASE CYLINDER ASSEMBLY N*m (kgf*cm, ft.*lbf): Specified torque - -

*A for LHD *B for 4WD *1 ECM *2 ENGINE WIRE *3 GLOVE COMPARTMENT DOOR ASSEMBLY *4 NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY N*m (kgf*cm, ft.*lbf): Specified torque - -

*A for LHD *B for 4WD *1 ECM *2 ENGINE WIRE *3 GLOVE COMPARTMENT DOOR ASSEMBLY *4 NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY N*m (kgf*cm, ft.*lbf): Specified torque - -

*A w/ Secondary Air Injection System *B w/o Secondary Air Injection System *C for RHD *D for LHD *1 ENGINE WIRE *2 NO. 1 FUEL HOSE *3 NO. 2 FUEL HOSE *4 NO. 4 AIR INJECTION SYSTEM HOSE *5 PURGE LINE HOSE *6 UNION TO CONNECTOR TUBE HOSE *7 BATTERY *8 BATTERY HOLD DOWN CLAMP *9 POSITIVE BATTERY TERMINAL *10 BATTERY TRAY *11 ENGINE ROOM RELAY BLOCK *12 NO. 1 RELAY BLOCK COVER SIDE *13 NO. 1 RELAY BLOCK COVER UPPER *14 NO. 2 ENGINE WIRE *15 SENSOR BRACKET - - N*m (kgf*cm, ft.*lbf): Specified torque - -

*A for 4WD - - *1 FRONT AXLE HUB GREASE CAP LH *2 FRONT AXLE SHAFT NUT LH *3 FRONT DRIVE SHAFT ASSEMBLY LH *4 FRONT DRIVE SHAFT HOLE SNAP RING *5 FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH *6 FRONT SPEED SENSOR LH *7 TIE ROD END SUB-ASSEMBLY LH *8 LOCK CAP Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part Differential oil MP grease Do not apply lubricants to the threaded parts

*A for LHD - - *1 POWER STEERING LINK ASSEMBLY *2 STEERING SLIDING YOKE Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque

*A for RHD - - *1 POWER STEERING LINK ASSEMBLY *2 STEERING SLIDING YOKE Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque

*A for 4WD - - *1 FRONT DIFFERENTIAL CARRIER ASSEMBLY *2 FRONT DIFFERENTIAL BREATHER HOSE *3 FRONT NO. 1 DIFFERENTIAL SUPPORT *4 FRONT NO. 2 DIFFERENTIAL SUPPORT *5 FRONT NO. 3 DIFFERENTIAL SUPPORT *6 DIFFERENTIAL MOUNT NUT *7 UPPER DIFFERENTIAL MOUNT STOPPER *8 LOWER DIFFERENTIAL MOUNT STOPPER *9 DIFFERENTIAL BREATHER TUBE BRACKET *10 WIRE HARNESS Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque Do not apply lubricants - -

*A for 2WD - - *1 FRONT EXHAUST PIPE ASSEMBLY *2 PROPELLER SHAFT GUARD *3 PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY *4 COMPRESSION SPRING *5 EXHAUST PIPE SUPPORT *6 GASKET *a for Differential Type BD22 *b for Differential Type BD20 Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part Do not apply lubricants

*A for 4WD - - *1 FRONT EXHAUST PIPE ASSEMBLY *2 FRONT PROPELLER SHAFT ASSEMBLY *3 PROPELLER SHAFT GUARD *4 PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY *5 COMPRESSION SPRING *6 EXHAUST PIPE SUPPORT *7 GASKET - - Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part Do not apply lubricants

*A for Manual Transmission *B w/o Console Box Lid *C w/ Console Box Lid *D w/ Rear Console Box *1 CONSOLE BOX CARPET *2 FRONT CONSOLE BOX COVER *3 FRONT CONSOLE BOX *4 REAR CONSOLE BOX SUB-ASSEMBLY *5 SHIFT LEVER KNOB SUB-ASSEMBLY *6 UPPER CONSOLE PANEL SUB-ASSEMBLY

*A for R151 - - *1 MANUAL TRANSMISSION UNIT ASSEMBLY *2 GROUND CABLE *3 MANIFOLD STAY *4 NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY *5 REAR NO. 1 ENGINE MOUNTING INSULATOR *6 SHIFT LEVER ASSEMBLY *7 SHIFT LEVER BOOT ASSEMBLY *8 WIRE HARNESS *9 NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY - - Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque

*A for R151F - - *1 MANUAL TRANSMISSION UNIT ASSEMBLY *2 GROUND CABLE *3 MANIFOLD STAY *4 NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY *5 REAR NO. 1 ENGINE MOUNTING INSULATOR *6 SHIFT LEVER ASSEMBLY *7 SHIFT LEVER BOOT ASSEMBLY *8 WIRE HARNESS Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque

*A for AC60E - - *1 AUTOMATIC TRANSMISSION ASSEMBLY *2 CLAMP *3 DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT *4 FLYWHEEL HOUSING DUST SEAL *5 GROUND CABLE *6 MANIFOLD STAY *7 NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY *8 OIL COOLER TUBE SUB-ASSEMBLY *9 REAR NO. 1 ENGINE MOUNTING INSULATOR *10 TRANSMISSION CONTROL CABLE ASSEMBLY *11 WIRE HARNESS *12 TRANSMISSION INSULATOR RH *13 WIRE HARNESS CLAMP BRACKET *14 NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY *a Black: x 1 Silver: x 5 - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

*A for AC60F - - *1 AUTOMATIC TRANSMISSION ASSEMBLY *2 CLAMP *3 DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT *4 FLYWHEEL HOUSING DUST SEAL *5 GROUND CABLE *6 MANIFOLD STAY *7 NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY *8 OIL COOLER TUBE SUB-ASSEMBLY *9 REAR NO. 1 ENGINE MOUNTING INSULATOR *10 TRANSMISSION CONTROL CABLE ASSEMBLY *11 WIRE HARNESS *12 TRANSMISSION INSULATOR RH *a Black: x 1 Silver: x 5 - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

*A for Manual Transmission - - *1 CLUTCH COVER ASSEMBLY *2 CLUTCH DISC ASSEMBLY *3 ENGINE ASSEMBLY *4 FLYWHEEL SUB-ASSEMBLY *5 REAR END PLATE *6 FLYWHEEL HOUSING DUST SEAL N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part ★ Precoated part - - *T1 1st: 26.5 (270, 20) 2nd: Turn 90° - -

*A for Automatic Transmission - - *1 DRIVE PLATE AND RING GEAR SUB-ASSEMBLY *2 REAR END PLATE *3 ENGINE ASSEMBLY *4 FRONT DRIVE PLATE SPACER *5 REAR DRIVE PLATE SPACER - - N*m (kgf*cm, ft.*lbf): Specified torque Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent ★ Precoated part - -

*1 FRONT ENGINE MOUNTING HEAT INSULATOR RH *2 FRONT ENGINE MOUNTING INSULATOR *3 ENGINE HANGER - - N*m (kgf*cm, ft.*lbf): Specified torque - -