ENGINE UNIT REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

  • Replacement of throttle with motor body assembly

  • Cleaning the deposits from the throttle with motor body assembly

  • Replacement of cylinder head sub-assembly

  • Replacement of camshaft (for intake or exhaust camshaft)

  • Replacement of camshaft timing gear assembly

  • Replacement of camshaft timing exhaust gear assembly

  • Replacement of fuel injector assembly

  • Replacement of engine coolant temperature sensor

  • Replacement of spark plug

  • Replacement of ignition coil assembly

  • Replacement of knock sensor

 Inspection after repair Poor idle, engine start, etc.

Click here

PROCEDURE


  1. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

    Click here

  2. REMOVE FUEL DELIVERY PIPE WITH FUEL INJECTOR

    Click here

  3. REMOVE PURGE VSV

    Click here

  4. REMOVE PCV PIPE


    1. A01W9DG

      Disconnect the PCV hose from the PCV valve sub-assembly and intake manifold.

    2. Remove the bolt and PCV pipe.

  5. REMOVE INTAKE MANIFOLD

    Click here

  6. REMOVE ENGINE WIRE


    1. Disconnect the connectors and clamps of the engine wire connected to the engine assembly.

    2. A01WA84

      Remove the 3 bolts and engine wire from the engine assembly.

  7. REMOVE HEATER HOSE


    1. A01W84ZC01
      *A for LHD
      *B for RHD

      Slide the 2 clamp and remove the heater hose from the cylinder head sub-assembly and No. 1 water by-pass pipe.

  8. REMOVE NO. 1 WATER BY-PASS HOSE


    1. A01W8EO

      Slide the clamp and remove the No. 1 water by-pass hose from the cylinder head sub-assembly.

  9. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH


    1. A01WBAZ

      Remove the 4 bolts and front No. 1 engine mounting bracket LH.

  10. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    1. A01WAD5

      Remove the 4 bolts and front No. 1 engine mounting bracket RH.

  11. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o Secondary Air Injection System)

    Click here

  12. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ Secondary Air Injection System)

    Click here

  13. REMOVE NO. 4 INTAKE PIPE (w/ Secondary Air Injection System)

    Click here

  14. REMOVE AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

    Click here

  15. REMOVE EXHAUST MANIFOLD

    Click here

  16. REMOVE IGNITION COIL ASSEMBLY

    Click here

  17. REMOVE GENERATOR ASSEMBLY

    Click here

  18. REMOVE IDLE PULLEY ASSEMBLY


    1. A01W9AA

      Loosen the bolt and then remove the idle pulley assembly.

      Tech Tips

      The bolt in the illustration cannot be removed from the idle pulley assembly.

  19. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET


    1. A01W9JO

      Remove the 5 bolts and No. 1 compressor mounting bracket.

  20. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

    Click here

  21. REMOVE NO. 1 WATER BY-PASS PIPE


    1. A01WAFJ

      Remove the 2 nuts, No. 1 water by-pass pipe and gasket.