ENGINE ASSEMBLY COMPONENTS

*1 AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE *2 AIR CLEANER CASE SUB-ASSEMBLY *3 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY *4 HOOD SUB-ASSEMBLY *5 INTAKE AIR CONNECTOR *6 NO. 1 AIR HOSE *7 NO. 2 PCV HOSE *8 VACUUM HOSE N*m (kgf*cm, ft.*lbf): Specified torque - -

*1 FRONT FENDER SEAL LH *2 FRONT FENDER SEAL RH *3 FRONT UPPER FENDER APRON SEAL LH *4 FRONT UPPER FENDER APRON SEAL RH *5 NO. 1 RADIATOR AIR GUIDE - - ● Non-reusable part - -

*1 FAN SHROUD *2 NO. 1 ENGINE UNDER COVER *3 NO. 1 ENGINE UNDER COVER ASSEMBLY *4 RADIATOR ASSEMBLY *5 RADIATOR HOSE INLET *6 RADIATOR HOSE OUTLET *7 RADIATOR RESERVOIR *8 RADIATOR DRAIN COCK PLUG *9 FAN AND GENERATOR V BELT *10 FAN PULLEY *11 FLUID COUPLING FAN *12 GROMMET *13 O-RING *14 WIRE HARNESS *15 CLAMP - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

*1 COOLER COMPRESSOR ASSEMBLY *2 ENGINE OIL LEVEL DIPSTICK *3 ENGINE OIL LEVEL DIPSTICK GUIDE *4 HEATER WATER OUTLE HOSE *5 HEATER WATER INLET HOSE *6 STARTER ASSEMBLY *7 VANE PUMP ASSEMBLY *8 CLUTCH RELEASE CYLINDER ASSEMBLY *9 O-RING *10 STUD BOLT N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

*1 ECM *2 GLOVE COMPARTMENT DOOR ASSEMBLY *3 ENGINE WIRE - - N*m (kgf*cm, ft.*lbf): Specified torque - -

*1 NO. 1 FUEL HOSE *2 NO. 2 FUEL HOSE *3 PURGE LINE HOSE *4 UNION TO CONNECTOR TUBE HOSE *5 BATTERY *6 BATTERY HOLD DOWN CLAMP *7 BATTERY POSITIVE TERMINAL *8 BATTERY TRAY *9 ENGINE ROOM RELAY BLOCK *10 NO. 1 RELAY BLOCK COVER SIDE *11 NO. 1 RELAY BLOCK COVER UPPER *12 ENGINE WIRE *13 NO. 2 ENGINE WIRE *14 SENSOR BRACKET N*m (kgf*cm, ft.*lbf): Specified torque - -

*1 FRONT EXHAUST PIPE ASSEMBLY *2 PROPELLER SHAFT GUARD *3 PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY *4 COMPRESSION SPRING *5 EXHAUST PIPE SUPPORT *6 GASKET Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part Do not apply lubricants

*A w/ Rear Console Box - - *1 CONSOLE BOX CARPET *2 SHIFT LEVER KNOB SUB-ASSEMBLY *3 FRONT CONSOLE BOX SUB-ASSEMBLY *4 REAR CONSOLE BOX SUB-ASSEMBLY *5 SHIFT LEVER KNOB SUB-ASSEMBLY - -

*1 MANUAL TRANSMISSION UNIT ASSEMBLY *2 GROUND CABLE *3 MANIFOLD STAY *4 NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY *5 REAR NO. 1 ENGINE MOUNTING INSULATOR *6 SHIFT LEVER ASSEMBLY *7 SHIFT LEVER BOOT ASSEMBLY *8 WIRE HARNESS *9 NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY - - Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque

*1 CLUTCH COVER ASSEMBLY *2 CLUTCH DISC ASSEMBLY *3 ENGINE ASSEMBLY *4 FLYWHEEL SUB-ASSEMBLY *5 REAR END PLATE *6 FLYWHEEL HOUSING DUST SEAL N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part ★ Precoated part - - *T1 1st: 26.5 (270, 20) 2nd: Turn 90° - -

*1 ENGINE HANGER *2 FRONT ENGINE MOUNTING HEAT INSULATOR RH *3 FRONT ENGINE MOUNTING INSULATOR - - N*m (kgf*cm, ft.*lbf): Specified torque - -