ENGINE ASSEMBLY COMPONENTS

*A for Automatic Transmission - - *1 HOOD SUB-ASSEMBLY *2 NO. 1 ENGINE UNDER COVER ASSEMBLY *3 NO. 2 ENGINE UNDER COVER *4 RADIATOR ASSEMBLY *5 RADIATOR RESERVE TANK ASSEMBLY *6 VANE PUMP OIL RESERVIOR ASSEMBLY *7 WASHER HOSE *8 FAN SHROUD *9 NO. 1 RADIATOR HOSE *10 NO. 2 RADIATOR HOSE *11 FLUID COUPLING ASSEMBLY *12 FAN PULLEY *13 FAN AND GENERATOR V BELT *14 NO. 1 OIL COOLER INLET HOSE *15 NO. 1 OIL COOLER OUTLET HOSE - - N*m (kgf*cm, ft.*lbf): Specified torque - -

*1 INTERCOOLER ASSEMBLY *2 NO. 1 ENGINE COVER SUB-ASSEMBLY *3 NO. 1 AIR HOSE *4 VACUUM HOSE *5 NO. 2 AIR HOSE - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

*A for LHD - - *1 ENGINE WIRE *2 GLOVE COMPARTMENT DOOR ASSEMBLY

*A for RHD - - *1 ENGINE WIRE *2 GLOVE COMPARTMENT DOOR ASSEMBLY

*A for LHD *B for RHD *1 AIR CLEANER CAP AND HOSE *2 AIR CLEANER CASE SUB-ASSEMBLY *3 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY *4 ENGINE WIRE *5 NO. 1 FUEL HOSE *6 NO. 2 FUEL HOSE *7 UNION TO CONNECTOR TUBE HOSE - - N*m (kgf*cm, ft.*lbf): Specified torque - -

*1 BATTERY *2 BATTERY CLAMP SUB-ASSEMBLY *3 BATTERY TRAY *4 WATER HOSE SUB-ASSEMBLY *5 NO. 1 RELAY BLOCK UPPER *6 NO. 1 RELAY BLOCK SIDE *7 NO. 2 ENGINE WIRE *8 WIRE TO WIRE *9 ENGINE ROOM MAIN WIRE - - N*m (kgf*cm, ft.*lbf): Specified torque - -

*1 COOLER COMPRESSOR ASSEMBLY *2 PRESSURE FEED TUBE ASSEMBLY *3 UNION TO CONNECTOR TUBE HOSE - - N*m (kgf*cm, ft.*lbf): Specified torque * For use with union nut wrench

*1 FRONT EXHAUST PIPE ASSEMBLY *2 GASKET *3 COMPRESSION SPRING - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

*1 FRONT PROPELLER SHAFT ASSEMBLY *2 PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY *3 TRANSFER CASE PROTECTOR LOWER *4 PROPELLER SHAFT GUARD Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque Do not apply lubricants to the threads - -

*A for Manual Transmission - - *1 UPPER CONSOLE PANEL ASSEMBLY *2 SHIFT LEVER KNOB SUB-ASSEMBLY *3 SHIFT LEVER BOOT ASSEMBLY *4 FLOOR SHIFT LEVER ASSEMBLY *5 CONSOLE BOX ASSEMBLY - -

*A for LHD - - *1 STEERING SLIDING YOKE *2 POWER STEERING LINK ASSEMBLY Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque

*A for RHD - - *1 STEERING SLIDING YOKE *2 POWER STEERING LINK ASSEMBLY Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque

*1 FRONT DIFFERENTIAL CARRIER ASSEMBLY *2 FRONT DRIVE SHAFT ASSEMBLY LH *3 FRONT DRIVE SHAFT ASSEMBLY RH *4 FRONT PROPELLER SHAFT ASSEMBLY *5 OIL TEMPERATURE SENSOR *6 FRONT DIFFERENTIAL BREATHER HOSE *7 FRONT DRIVE SHAFT HOLE SNAP RING *8 FRONT NO. 1 DIFFERENTIAL SUPPORT *9 FRONT NO. 2 DIFFERENTIAL SUPPORT *10 FRONT NO. 3 DIFFERENTIAL SUPPORT *11 DIFFERENTIAL MOUNT NUT *12 UPPER DIFFERENTIAL MOUNT STOPPER *13 LOWER DIFFERENTIAL MOUNT STOPPER *14 DIFFERENTIAL BREATHER TUBE BRACKET *15 WIRE HARNESS - - Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf) : Specified torque ● Non-reusable part Differential oil MP grease Do not apply lubricants

*A for Manual Transmission - - *1 MANUAL TRANSMISSION UNIT ASSEMBLY *2 STIFFENER PLATE RH *3 STIFFENER PLATE LH *4 STARTER ASSEMBLY *5 CLUTCH RELEASE CYLINDER ASSEMBLY *6 REAR ENGINE MOUNTING INSULATOR *7 NO. 3 FRAME CROSS MEMBER SUB-ASSEMBLY - - Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) N*m (kgf*cm, ft.*lbf): Specified torque Do not apply lubricants to the threads - -

*A for Automatic Transmission - - *1 AUTOMATIC TRANSMISSION ASSEMBLY *2 DRIVE PLATE AND TORQUECONVERTER SETTING BOLT *3 OUTLET OIL COOLER TUBE *4 INLET OIL COOLER TUBE *5 STIFFNER PLATE RH *6 NO. 4 CYLINDER BLOCK INSULATOR *7 NO. 2 END PLATE *8 STIFFNER PLATE LH *9 STARTER ASSEMBLY *10 TRANSMISSION CONTROL CABLE BRACKET *11 REAR ENGINE MOUNTING INSULATOR *12 NO. 3 FRAME CROSS MEMBER SUB-ASSEMBLY N*m (kgf*cm, ft.*lbf): Specified torque Do not apply lubricants to the threads

*A for Automatic Transmission *B for Manual Transmission *1 CLUTCH COVER ASSEMBLY *2 CLUTCH DISC ASSEMBLY *3 FLYWHEEL SUB-ASSEMBLY *4 REAR END PLATE *5 PUMP IMPELLER DRIVE PLATE *6 REAR DRIVE PLATE SPACER N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

*1 ENGINE HANGER *2 ENGINE HANGER *3 FRONT ENGINE MOUNTING INSULATOR - - N*m (kgf*cm, ft.*lbf): Specified torque - -