SFI SYSTEM, Diagnostic DTC:P0011, P0012

DTC Code DTC Name
P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)
P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1)

DESCRIPTION

Refer to DTC P0010.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).

  • Valve timing

  • Camshaft timing oil control valve assembly (for intake side)

  • Oil control valve filter

  • Camshaft timing gear assembly (for intake side)

  • ECM

 Comes on DTC stored
P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).

  • Valve timing

  • Camshaft timing oil control valve assembly (for intake side)

  • Oil control valve filter

  • Camshaft timing gear assembly (for intake side)

  • ECM

 Comes on DTC stored

MONITOR DESCRIPTION



MONITOR STRATEGY

Required Sensors/Components (Main)

Camshaft timing oil control valve assembly (for intake side)

Camshaft timing gear assembly
Required Sensors/Components (Related)

Crankshaft position sensor

Camshaft position sensor

Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

B0026RHE42

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the ignition switch off and wait for at least 30 seconds.

  5. Turn the ignition switch to ON and turn the GTS on [A].

  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

  7. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Idle the engine for 3 minutes or more [D].

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  12. Input the DTC: P0011 or P0012.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].

  14. Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    Tech Tips

    Depress the accelerator pedal by a large amount.

  15. Idle the engine for 3 minutes or more [G].

  16. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].

  17. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  18. Check the DTC judgment result again.

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

Refer to DTC P0010.

Click here

CAUTION / NOTICE / HINT

Tech Tips


  • DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P0011 or P0012 is output A
      DTC P0011 or P0012 and other DTCs are output B

      Tech Tips

      If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Turn the A/C switch on.

    5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).


      Powertrain > Engine > Active Test
      Tester Display
      Control the VVT Linear (Bank1)

    6. Check the engine speed while operating the camshaft timing oil control valve assembly (for intake side) using the GTS.

      OK
      GTS Operation Specified Condition
      0% Normal engine speed
      100% Engine idles roughly or stalls

      Tech Tips


      • Refer to "Data List / Active Test" [VVT OCV Duty #1 and VVT Change Angle #1].

        Click here

      • If the result is not acceptable, cool the engine (engine coolant temperature is 50°C (122°F) or less) and perform the Active Test again.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) Click here

    OK

  3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    11. Read the pending DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC is not output A
      DTC P0011 or P0012 is output B

      Tech Tips

      DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.


    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

  4. CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)


    1. B0028CWC02
      *a Timing Mark
      *b Groove
      *c Approximately 13°

      Remove the cylinder head cover sub-assembly.

    2. Turn the crankshaft to align the timing marks of the crankshaft.

    3. Align the groove of the crankshaft pulley with the "0" position.

    4. Confirm whether the timing marks of the camshaft pulley and cylinder head cover are facing each other.

      Tech Tips

      If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

      OK
      The timing marks of the camshaft pulley and the cylinder head cover face each other when the groove of the crankshaft pulley is in the "0" position.
      Result
      Proceed to
      OK
      NG

    NG

    CHECK ENGINE MECHANICAL SYSTEM Click here

    OK

  5. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE)


    1. Inspect the camshaft timing oil control valve assembly (for intake side).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE) Click here

    OK

  6. INSPECT OIL CONTROL VALVE FILTER


    1. Remove the oil control valve filter.

      Click here

    2. Check that the filter is not clogged.

      OK
      Filter is not clogged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OIL CONTROL VALVE FILTER Click here

    OK

  7. REPLACE CAMSHAFT TIMING GEAR ASSEMBLY


    1. Replace the camshaft timing gear assembly.

      Click here

      Tech Tips

      Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    11. Read the pending DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC is not output A
      DTC P0011 or P0012 is output B

    A

    END

    B

    REPLACE ECM Click here